Eggtimer Rocketry Eggtimer Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 56

Eggtimer Rocketry Eggtimer Скачать руководство пользователя страница 54

- 54 -

Eggtimer Quick Reference (Release 1.48b)

Typical Flight Sequence

1) Long Beep – Power On
2) Short Beep-Beep for 30 seconds – Programming Mode (Terminal, or hold button for Pre-Programmed Flight)
3) Pause while baseline samples are taken and self-test is executed  (about 10 seconds)
4) Long Beep (Self-Test passed ) OR Beep Codes (Self-Test failed)
5) Chirping – Ready for Launch

Launch….

6)  Deployment/Airstart channels fire as programmed during flight
7)  At landing (< 30 ft for 5 seconds), the altitude is beeped out OR elapsed time/apogee is sent continuously over
the data port if the Telemetry option was enabled.

Beep Codes

Number of Beeps

Problem

1

Battery Low ( < 2.8v)

2

Altimeter Sensor or Hardware Error

3

Breakwire open (airstarts only)

4

Channel A (Main) error - igniter/servo/battery

5

Channel B (Drogue/Airstart) error – igniter/servo/battery

Pre-Programmed Flight Settings

To program, hold button during Programming Mode (Beep-Beep after power up) until the beep code matching the
flight profile that you want to use is beeped out. Release the button, you will hear a long Beep, followed by a repeat
of the Beep Code, then the Eggtimer halts. Perform a Reset or power it down and back up before flying.

Profile No.

LDA

Ascent
Samples/Sec

Main Channel

CHB Channel

1

100

10

Off

Off

2

200

20

Off

Off

3

100

10

Nose-Over

Off

4

200

20

Nose-Over

Off

5

200

10

500’

Nose-Over

6

200

20

500’

Nose-Over

7

200

10

800’

Nose-Over

8

200

20

800’

Nose-Over

1 – Flight Recording Only, no deployment, low-medium power
2 – Flight Recording Only, no deployment, medium-high power
3 – Single Deployment at Nose-Over, low-medium power
4 – Single Deployment at Nose-Over, medium-high power
5 – Multiple Deployment, Main at 500’, medium power
6 – Multiple Deployment, Main at 500’, medium-high power
7 – Multiple Deployment, Main at 800’, medium power
8 – Multiple Deployment, Main at 800’, medium-high power

Cable Connections/Settings

Connections:  GND – Black;   RX – Red/Green;  TX – White
Serial Port Settings:  19200 baud, 8 bits, 1 stop bit, no parity, no handshaking
Emulation:  ANSI/VT100

«
...
52
53
54
55
56
»

Содержание Eggtimer

























































Отзывы:

Нет отзывов