manualshive.com logo in svg

Eggtimer Rocketry Eggtimer, Руководство пользователя, Страница: 3 / 56

Поделиться
Скачать
Eggtimer Rocketry Eggtimer Скачать руководство пользователя страница 3

 

- 3 - 

Disclaimers, Legal Stuff, Etc. 

 
The Eggtimer is meant to be used for hobby and experimental rocketry purposes.  Although 
hobby rocketry has an admirable safety record, largely due to the efforts of the good people at 
the National Association of Rocketry (NAR) and the Tripoli Rocketry Association (TRA), 
rocketry can be dangerous if proper safety precautions are not observed.  This is particularly true 
with some of the advanced techniques like pyrotechnic parachute deployment and igniting rocket 
motors in flight (“Airstarts”).   People can and have been seriously injured by not following 
recognized and accepted safety practices.  We cannot be responsible for your actions.   
 
We 

strongly

 recommend that if you are not a member of either the NAR or the TRA, you join 

one of them, join a local rocketry club, and pick the brains of experienced members before you 
try any kind of multiple deployment or airstart flight.  The safety information included in these 
instructions is by no means comprehensive or complete, and is no substitute for the supervision 
and advice of experienced rocketeers.  
 

Limited Warranty 

 
Eggtimer Rocketry warrants that all of the parts on the packing list of the Eggtimer kit have been 
included, and that they are all in working condition.   If you are missing something, contact us 
immediately at 

[email protected]

 and we will send you whatever it is that you are 

missing.  If you are missing something really egregious (like the PC board or the processor, for 
example), we may ask you to return the entire kit unbuilt, we will send you a prepaid shipping 
label for this purpose.  We’d especially like to see the packing list so we can figure out what 
went wrong so it doesn’t happen again… 
 
If your Eggtimer does not work properly after assembly, take a deep breath, get out the 
magnifying glass and a good light, and see if you have inadvertently created a solder bridge 
somewhere.  Chances are pretty good that you have, or that you have installed a part incorrectly.  
We are a very small company and we just don’t have the resources to repair your board, but we 
will be more than happy to give you advice and we might be able to help you find your error if 
you send us some high resolution pictures, to 

[email protected]

 .  We cannot take 

responsibility for your assembly techniques; if you do not have experience building kits of this 
nature, we recommend that you enlist some help. (Another reason for joining a rocketry club, 
there is usually at least one electronically-inclined member who can be bribed with a beverage or 
two to give you a hand.  Engineering types love a challenge, especially it it’s easy for them but 
hard for you.) 
 
Eggtimer Rocketry warrants that when properly assembled the Eggtimer will perform 
substantially according to the published documentation.  This means that we spent a lot of time 
trying to ensure that it’s going to work the way that we say it does, and we try to fix things that 
don’t quite work right in a reasonable time.  Nevertheless, we can not and do not warrant that the 
Eggtimer is perfect and will meet every rocketry purpose, for the simple reason that we can’t test 
every possible rocket/motor/environmental combination.  It is the buyer’s responsibility to 
determine the suitability of the Eggtimer for their particular purpose.  If you have a problem with 
this, please contact us and we will be happy to send you a prepaid return label for your unbuilt 
Eggtimer kit and we will refund your purchase price. 
 

Содержание Eggtimer

























































Отзывы:

Нет отзывов