background image

UPS RMH700/1000/1500 

 

Instruction Manual 

RMH Series 

 

 

Page 7 of 37

 

3 Safety 

3.1  General safety instructions 

 

Read and observe the user manual and safety instructions in this chapter before 
taking any further action (transportation, storage, connection, startup, etc.). 

 

Since the UPS equipment uses mains voltage and incorporates an appropriate 
energy accumulator (high-capacity batteries) either on the inside or outside of 
the device, the instructions in this chapter are very important for all users and 
personnel. For this reason, safety information on batteries and battery packs is 
also provided here. When using external battery packs, you must also follow the 
safety instructions in the accompanying manual. 

 

Work on the UPS equipment may only be performed by authorized technical 
personnel. 

3.2  Transportation and storage 

The UPS may only be transported to its destination in the original packaging. 
The same applies for removals or returns. 

The equipment may not be transported or stored upside down. 

Position the equipment securely during transportation taking the centre of 
gravity into account. Due to their weight, UPS equipment with built-in batteries 
may drop suddenly if their position shifts slightly. 

During storage, secure positioning of the equipment must also be ensured. 

3.3 Setup 

The UPS is intended for use in ventilated rooms. 

During setup or installation, the installation location prescribed by the 
manufacturer must be observed. 

If the UPS is exposed to extreme and rapid temperature changes, there is a 
risk of condensation. Before taking any further steps, the equipment should be 
allowed to acclimatise for at least 2 hours. 

Never set up or operate the equipment in a damp environment. 
Keep fluids away from the equipment. 

Содержание ME 1500






































Отзывы: