Effecta Smart 40 Скачать руководство пользователя страница 37

Страница: 37 / 43

Effecta AB - Västra Rågdalsvägen 21 - 434 99 Kungsbacka - 0300 - 22320 - [email protected]

▀

Troubleshooting

Problem

Possible errors

Action

The fan will not start

- The fan is turned off
- Boiler overhetaed
- Faulty start capacitor
- Faulty fan motor

- Press start new firing
- Reset overheat protection
- Contact installer
- Replace the fan

Smoke is seeping through the doors.

- Leaking gasket

- Adjust the doors

White smoke from the chimney

- Low flue gas temperature
- Too big chimney
- Rain water in the chimney

- Cut turbulators/increase effect
- Contact installer
- Mount a rain hood

Black smoke from the chimney,
poor combustion

- Moist wood
- Sooty boiler

- Change wood
- Clean according to manual

Boiler overheated

- Air in the system
- Too large insert of wood

- Bleed the system
- Adjust amount of wood

Tar in the convection section.

- A sooty loading compartment
- Sooty combustion plate
- Moist wood
- Leaking gasket

- Clean loading compartment
- Clean combustion plate
- Fire with dry wood
- Check for leakage in the gaskets

Little or no heat is transferred to the
accumulator tank.

- Air in the system
- Moist wood

- Refill the system thoroughly
- Use more dry wood, or finely chopped

The boiler has a low output and is sluggish.

- Moist wood
- The boiler may need a cleaning

- Use more dry wood
- Clean the boiler

The loading pump creaks or thumps,

- Probably air in the system
- Low system pressure

- Follow the instructions for Laddomat
- Increase the pressure

The pressure drops in the system.

- There is a leakage in the system
- Wrong first pressure in the pressure vessel

- Fill with water and bleed
- Adjust the pressure

Noise from the fan.

- The cooling wing scrapes against the boiler.
- The bearings in the fan have run out.

- Check the cooling wing
- Change the fan

High flue gas temperature.

- Soot in the tubes in the convection

- Clean the tubes

No heat on radiators
(only if shunt is controlled from the boiler)

- Shunt motor closed
- Shunt motor is broken
- Radiator pump is not activated
- Radiator pump is broken
- Air in the radiator circuit

- Contact installer
- Contact installer
- Activate in the shunt control
- Contact installer
- Bleed the circuit

A sensor shows wrong temperature

- Faulty sensor
- Calibrate

- Change sensor
- Cal/- in the menu "Other"

Incorrect lambda value

- Dirty lambda probe
- Faulty lambda probe

- Clean the probe
- Change the lambda probe

Содержание Smart 40












































Результаты поиска

Содержание Smart 40

Отзывы:

Похожие инструкции для Smart 40

Бренды по названию

Популярные бренды

Effecta Smart 40, Установка, обслуживание, сервис, сборка.

Результаты поиска

Содержание Smart 40

Отзывы:

Похожие инструкции для Smart 40

Бренды по названию

Популярные бренды