manualshive.com logo in svg

Efco Swaploader SL-330, Руководство по эксплуатации и частям

Поделиться
Скачать
Efco Swaploader SL-330 Скачать руководство пользователя страница 39

 

SL-330.INS

 

 

 

 

 

 

 

2-17

 

09/2009 

HOW TO IDENTIFY WHAT PUMP IS NEEDED 

 
The SwapLoader factory supplied pump is a bushing style gear pump, because of the pressure 
requirements of the SwapLoader hooklift hoist.  By design the bushing style pumps are single 
rotation (rotation specific). 
 
All SwapLoader hooklift hoists come standard with a CCW (left hand rotation pump), which will 
work for most manual transmission applications.  For most automatic transmission applications a 
CW (right hand rotation pump) is needed; call SwapLoader for price and availability.  

NOTE:  

Consult the PTO supplier whenever uncertain about the correct pump rotation for a 
particular application.

 

 
The table below lists the SwapLoader part number for both left and right hand rotation pumps for 
the SL-330 hoist model: 
 

MODEL 

L.H. Rotation 

Pump (standard)

R.H. Rotation 

Pump (special) 

SL-330 20P87 

21P03 

 
 

HOW TO IDENTIFY PUMP ROTATION 

 
To better understand the effects of pump rotation we must consider the path that oil takes 
through the pump.  Oil enters the pump through the inlet (suction) port, travels around the 
outside of the gears, and is forced out through the outlet (exhaust) port.  Oil enters and exits the 
pump in the direction of its rotation. 
 

BELLY DOWN

VIEW PUMP

VIEW  FROM

FRONT  OF  VEHICLE

OPPOSITE ENGINE ROTATION (PTO)

ENGINE ROTATION (PTO)

VIEW  FROM

REAR  OF  VEHICLE

OPPOSITE ENGINE ROTATION (PTO)

ENGINE ROTATION (PTO)

 

 
Determine pump rotation by positioning the pump belly side down (see illustration above).  
Looking at the rear of the pump if the suction (largest) port is to the left side, then the pump is a 
CCW or left hand rotation.  If the suction (largest) port is on the right side, then the pump is CW 
or right hand rotation. 

Содержание Swaploader SL-330







































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды