Efco Swaploader SL-330 страница 40 Скачать руководство пользователя | Manualshive

Страница: 40 / 134

background image

SL-330.INS

2-18

09/2009

PUMP INSTALLATION

1.

Install the hydraulic pump to the P.T.O. (Bolts are not provided).

2.

Install the hydraulic fittings into ports on the hydraulic pump as shown on Drawing No.
91H04.

3.

Connect the suction hose assembly to the hydraulic tank (1 1/2" I.D. hose) and route to
the hydraulic pump in as short and straight line as possible. Be sure to route the hose
clear of exhaust components and of the drive shaft. Extra hose is provided so the hose
can be shortened to an appropriate length. Install the hose on the hose barb fittings at the
tank and at the pump and secure with the hose clamps provided.

NOTE: Prior to startup, this hose must be filled with oil.

4.

The pressure hose the hydraulic pump to the control valve assembly is ant supplied with
the hoist as it must be made to the proper length. This hose must be purchased from a
local hydraulic hose assembly supplier per the following specifications:

Hose

I.D.:

3/4

inch

Working

Pressure:

3500

PSI

Hose Fitting Threads:

SAE 37° (JIC) 1 1/16-12

5.

Install the pressure hose as indicated. Tie up the pressure and suction hoses as necessary.
Again, be sure the hoses are routed to avoid exhaust components and to stay clear of the
drive shaft.

«
...
38
39
40
41
42
...
»

Содержание Swaploader SL-330







































































































































Отзывы:

Нет отзывов

Похожие инструкции для Swaploader SL-330

Бренд: RAM Commercial Страницы: 284

Automizer Versa Hand

Бренд: Labrie Страницы: 80

Бренд: Jet Страницы: 12

Бренд: Vestil Страницы: 9

Бренд: Snorkel Страницы: 96

Бренд: fetra Страницы: 100

Бренд: HELI Страницы: 20

Бренд: HELI Страницы: 105

Бренд: HELI Страницы: 110

Бренд: HELI Страницы: 131

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды