Efco Swaploader SL-330 страница 47 Скачать руководство пользователя | Manualshive

Страница: 47 / 134

background image

10/05/09

INSTALLATION INSTRUCTIONS

1.

Review all directions and diagrams provided before starting bumper installation.

2.

Trim truck frame to indicated dimensions (See Fig. 1). These dimensions will facilitate the

mounting of the rear light assembly if it is also being mounted.

3.

Measure the distance from the bottom of the truck frame to the ground (NOTE: This should

be performed on a level surface). Based this measurement and the dimensions in Fig.
1, the vertical channel [P/N: 63H94] may need to be modified in length to meet the
Office of Motor Carrier Safety (OMCS) regulations. Regulation 393.86 requires that no
bumper be located more than 30” off the ground when the truck is empty, and the end of
the bumper should not be located more than 24” from the extreme rear of the vehicle,
including truck bodies (See Fig. 2). Once the length has been determined for the
vertical channels, weld them to the truck frame (See additional notes on next page).

4.

Center the bumper weldment [P/N: 52H12] on the vertical channels [P/N: 63H94]. Position

rear of bumper from rear of the hoist as indicated by the bumper location chart. This is
crucial in order to ensure that the container longsills do not contact the bumper during
the dump cycle (See Fig. 1 & 2).

REAR BUMPER ASSEMBLY

(52H11)

FIG. 1

BUMPER LOCATION CHART

DIM B. (Max)

DIM. A

SL-105

SL-145 SL-180

SL-220/222

& SL-240

SL-2418

SL-330 &

SL-400

SL-406 &

SL-505/545

SL-650

24 5/8”

13 1/2

15 3/4

15 1/4

17

14 1/4

14

16 1/2

18

22 5/8”

12 1/4

14 1/2

14

15 3/4

13

12 3/4

15

20 5/8”

11

13

12 3/4

14 1/4

11 3/4

18 5/8”

9 3/4

11 3/4

11 1/2

All Figures are for Illustration Purposes Only

«
...
45
46
47
48
49
...
»

Содержание Swaploader SL-330







































































































































Отзывы:

Нет отзывов

Похожие инструкции для Swaploader SL-330

Бренд: RAM Commercial Страницы: 284

Бренд: HOLZMANN MASCHINEN Страницы: 31

Бренд: HOLZMANN MASCHINEN Страницы: 34

Бренд: Volvo Страницы: 128

Бренд: Scheppach Страницы: 112

Бренд: Jet Страницы: 12

Бренд: DAF Страницы: 352

Бренд: HSC Страницы: 13

Бренд: Jet Страницы: 12

Бренд: Total Source Страницы: 11

Бренд: Motrec Страницы: 47

Бренд: Motrec Страницы: 61

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды