background image

OVERFLOW PROTECTION 

 

When the liquid flows to the control panel, the hob will automatically shut down within 
10 seconds.

 

To restart, turn off the power and wipe the area with a clean towel before using.

 

 

OPERATION TIME LIMIT OF THE COOKING ZONE 
 

Each  cooking  zone  is  switched  off  automatically  after  a  maximum  preset  time  if  no 
further operation is performed. The maximum preset time limit depends on the set 
power level and the default cooking times are shown in the table below:

 

 

Power Level

 

1

 

2

 

3

 

4

 

5

 

6

 

7

 

8

 

9

 

P

 

Operation Time Limit 
(hour)

 

8

 

8

 

8

 

4

 

4

 

4

 

2

 

2

 

2

 

5

min

 

 

Each touch on the control key will reset the maximum operation time as initial default 
value. 

 
TIMER FUNCTION 

 

The 

timer can be used in two different ways:

 

 

As a minute minder. In this case, the timer will not turn any cooking zone off when 
the set time is up. It is function as a reminder or alarm.

 

 

As an automatic switch off timer - to turn one or more cooking zones off after the 
set time is up.

 

 

In both ways, the timer can be set from “01” to “99” minutes.

 

 

Using the Timer as a Minute Minder

 

The minute minder can be activated if there is no cooking zone selected 

 

1.

 

Make sure that the cooktop is turned on. 

 

Note: The minute minder can be activated before or after cooking zone setting is finished.

 

 

2.

 

Touch the timer control, the timer display will show “00”,

 

and the second digit “0”will flash.

 

 

 
 
 
 

Содержание HB BI 2721 A

























Отзывы: