Edwards HP20T, Руководство по безопасности и инструкция, Страница: 12 / 30

Horizontal Press Installation
This manual provides installation requirements for the Edwards
Horizontal Press.
All Edwards Hydraulic Accessory Tools are powered by an
Edwards Ironworker outfi tted with a Hydraulic Accessory Pack
or an Edwards Porta Power, portable hydraulic power unit.
Refer to Safety, Installation, Operations and Maintenance
manuals for the Edwards power-plant you are using to oper-
ate your Edwards Hydraulic Accessory Tool.
Environmental Requirements at Work Station
The work station environment for your Edwards Horizontal Press must
meet the following minimum requirements:
• Ambient temperature: 7.2°C - 43.3°C [45°F - 110°F]
• Relative humidity: No greater than 90% relative humidity.
• Floor area: Assure that the machinery work area provides
for a stable, adequately sized and load rated fl oor area for
material movement to and from the machinery work stations.
• Shelter: Protect your Ironworking machinery from water, salts
and corrosive elements.
• Lighting: 500LUX (50 footcandles) minimum.
Receiving the Horizontal Press
Edwards Hydraulic Accessory Tools are fully assembled and are shipped
either by palletized custom wooden crate or by shrink-wrapped wooden
pallet for ease of transport and receiving.
Inspect the packaging for damage and follow shipping/receiving instruc-
tions as listed on the packaging prior to receiving the tool into your
facility.
When receiving your Hydraulic Accessory Tool, be prepared to safely
move your machinery with a fork-lift rated for the following equipment
weights:
Minimum Machinery Weights
Horizontal Press 612.34kg/1350lb
Utilize best practices for fork-lift operation. Handle material as close
to the drive surface as possible with the widest spread and deepest pen-
etration of forks effective to service the pallet. Forks should be adjusted
and locked into the safety detent closest to the maximum available fork
spread.
Unpacking/Moving the Horizontal Press
Your Edwards Horizontal Press includes surface and remotely mounted
electrical cabling and hydraulic lines. Exercise caution when removing
the factory supplied packaging. Do not cut electrical wires or hydraulic
hoses.
1. Carefully remove packaging.
2. Carefully remove the lagbolts and washers attaching the HP20T to
the shipping pallet.
3. Locate the fork-lift areas at the bottom of the machinery
4. Carefully insert forks through the fork lift assembly. Confi rm that
forks penetrate through the assembly and allow for clamps to re-
strain Horizontal Press from sliding off forks. Install clamps (not
included) to forks so that the press is stable while moving and lift
the press from the pallet.
5. Locate your HP20T Horizontal Press directly adjacent to the Ed-
wards Ironworker or Porta Power. Ensure that power controls of the
Ironworker or Porta Power are within arms-reach of the Horizontal
Press.
Installing the Horizontal Press
1. The HP20T Horizontal Press is designed to mount on a dedicated,
weight rated fl ooring system. DO NOT MOUNT ON CASTERS. The
fl oor rating should be a minimum multiplier of 2.5 times the weight
of the Press plus the weight of any tooling being used within the
Press, plus the material being pressed.
2. Locate leveling pads installed on the bottom of the machine. Un-
screw pads to allow for a minimum of 1” working space and the in-
stallation of anchoring hardware (not provided). With a level placed
on the work surface, check the machinery for level. Adjust machine
for level by rotating pads clockwise or counterclockwise and mark
drill locations within leveling pad surface. Drill for and install four
1/2” wedge anchor bolts to secure HP20T to fl oor. Lower machine
onto anchor bolts, install washers, and tighten nuts to complete
fl oor installation.
( HP20T weight (1350 lb.) + Tooling Material weight )
x 2.5 = Dedicated, weight rated fl oor system
2