Edwards E-LAB 2 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 42

background image

A652–07–880 Issue D

Page ii

© Edwards Limited 2014. All rights reserved.

Edwards and the Edwards logo are trade marks of Edwards Limited.

Contents

Clean the pump oil level sight glass .................................................................................28

Clean the motor fan cover ............................................................................................30

Clean and overhaul the pump .........................................................................................30

Test the motor condition ..............................................................................................30

Fit new blades to the pump ...........................................................................................30

Fault finding ............................................................................................................. 31

The pump has failed to start ..........................................................................................31

The pump has failed to achieve the specified performance (has failed to reach ultimate vacuum) ......31

The pump is noisy ....................................................................................................... 31

The pump surface temperature is above 100 °C ...................................................................32

The vacuum is not fully maintained after the pump is switched off ...........................................32

The pumping speed is poor ............................................................................................32

There is an external oil leak ..........................................................................................32

Storage and disposal ........................................................................... 33

Storage ...................................................................................................................33

Disposal ................................................................................................................... 33

Service and spares .............................................................................. 35

Introduction .............................................................................................................35

Service .................................................................................................................... 35

Spares available .........................................................................................................35

For return of equipment, complete the HS Forms at the end of this manual.

«
...
2
3
4
5
6
...
»

Содержание E-LAB 2











































Отзывы:

Нет отзывов

Похожие инструкции для E-LAB 2

Бренд: York Страницы: 16

Бренд: TapFlo Страницы: 35

Бренд: Rainman Страницы: 17

Бренд: Vaillant Страницы: 40

Бренд: DAB Страницы: 40

Бренд: A.O. Smith Страницы: 44

Бренд: AromaMist Страницы: 15

Бренд: Amana Страницы: 26

Бренд: Graco Страницы: 48

Бренд: Rinnai Страницы: 67

Бренд: DROPSA Страницы: 9

Бренд: Elkay Страницы: 2

Бренд: esotec Страницы: 3

Бренд: German pool Страницы: 20

Бренд: T.I.P. Страницы: 72

Бренд: SHG Страницы: 32

Бренд: HAMMELMANN Страницы: 311

Бренд: OmarLift Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды