background image

RCX C-Link Series

Configuration and LED Configuration Codes

EDT, Inc.

2011 June 29

8

A first digit of 1 indicates that the unit is configured for the camera end; a first digit of 2 indicates that the unit 
is configured for the framegrabber end. The second digit must be the same for both ends (camera and 
framegrabber). With a FOX framegrabber, there is no extender at the framegrabber end, so the 
configuration code is set at the camera end only.

For a typical base-mode system, a configuration code of 1-1 at the camera end and 2-1 at the framegrabber 
end permits standard base-mode operation at clock frequencies of 20–40 MHz. For a typical full mode 
system, a configuration code of 1-4 on both extenders at the camera end, and a configuration code of 2-4 
on both at the framegrabber end, allows standard full-mode operation at clock frequencies of 60–80 MHz.

On the configuration code label for a medium- or full-mode system, 

X Channel

 refers to the primary MDR26 

connnector on the camera or framegrabber, and 

YZ Channel

 refers to the secondary connector.

Base Mode

Table 1

 shows the operating modes of an extender in base mode (EDT firmware revsion 11 or higher).

Cameras operating between 40 and 60 MHz are usually best served by configuration codes 1-3 and 2-3. If 
the camera needs only 16 data bits or fewer transferred per clock cycle (instead of all 24), it is possible to 
use configuration codes 1-2 and 2-2 instead, and thus operate the link at 1.25 GBaud for longer range and 
lower power dissipation. The selection of 16-bit mode is made only at the framegrabber end through 
configuration code 2-2, or through the directive

 mode16: 1 

in a FOX configuration file; this information is 

communicated over the fiber to the extender at the camera end. (At the camera end, configuration codes 
1-1 and 1-2 are identical.)

At reset (and whenever the extender cannot lock to the camera clock), the extender initializes to assume 
that the Camera Link Data-Valid signal is never asserted, and ignores it. Many Pulnix cameras do not assert 
Data-Valid, so this behavior is useful for those using such cameras. The first occurrence of Data-Valid true 
from the camera causes the extender to use Data-Valid to qualify video data from that point on.

In the case of a dual-tap camera, the Camera Link pixel clock is half the camera’s pixel rate. For example, 
a dual-tap 12-bit camera with a 40 MHz Camera Link clock sends 80 million pixels per second. This camera 
is compatible with the extender in configuration code 1-1.

Table 1.  LED configuration codes – base mode 

Code

End

Camera Clock Rate Constraints

Link Rate

Extender Type

1-1

camera

20–40 MHz

24 bits

1.25 GBaud

Fiber & coax

1-2

camera

20–60 MHz

16 bits

1.25 GBaud

Fiber & coax

1-3

camera

20–60 MHz

24 bits

2.5 GBaud

Fiber only

1-4

camera

60–80 MHz

24 bits

2.5 GBaud

Fiber only

2-1

framegrabber

40 MHz

24 bits

1.25 GBaud

Fiber & coax

2-2

framegrabber

60 MHz

16 bits

1.25 GBaud

Fiber & coax

2-3

framegrabber

60 MHz

24 bits

2.5 GBaud

Fiber & coax

2-4

framegrabber

80 MHz

24 bits

2.5 GBaud

Fiber only

3-3

firmware update (see 

Firmware on page 12)

1.25 GBaud

Fiber & coax

2 fast, 2 slow, 2 fast

Error: unsupported configuration code entered

Содержание RCX C-Link series



























Отзывы: