Edson 220A Series Скачать руководство пользователя страница 6

146 DUCHAINE BLVD., NEW BEDFORD, MA.  02745-1292    TEL.  508-995-9711    FAX  508-995-5021     E-MAIL  [email protected]

Running The Pump Dry:

This Pump will run dry indefinitely without damage.

Pumping Liquids with Suspended Solids:

l

KEEP SOLIDS IN SUSPENSION - When the pump

is used to pump solid matter such as sludge at

the bottom of a tank, or to dredge out a section of a

lagoon make, sure the solids have enough liquid

mixed in to allow it to flow. Raking or stirring while

the pump is pumping will keep solids in

suspension. Rule of thumb in pumping viscous

liquids or combinations of liquids with solids, "If It

Will Not Flow Through A Line Under Gravity, The

Pump Will Most Likely Not Pump It."

l

FLAPPER CHECK VALVES AND SOLIDS -

Solids trapped under the check valves will

prevent self priming. This is likely to occure when

the pump is used in sewage or sump pump out

applications . Flushing with water will generally

clear out the solid matter. Installing secondary

clear flapper check valves right at the inlet and

discharge will improve the dry suction start

performance of the pump and make clearing the

valves easy. Order Edson Clear Check Valves

69CL-150 (1.5").

l

PUMPING AT THE PROPER SPEED -  When

pumping liquid with solids the speed may be too

slow to keep the solids and the liquid combined.

The solids will stop moving and begin to clog the

line. Pumping at a faster rate or decreasing the

hose size to increase velocity may be the solution.

Check With Edson Customer Service.

l

USING A STRAINER ON THE INLET -  If the

solids are too large they will block the inlet or get

stuck in the suction line. The end a suction hose

can become attached to a flat surface cutting off

all flow. Using an Edson strainer will prevent

these conditions. Order an Edson Shatterproof

Bronze Strainer 111BR - 150

l

USING A DISCHARGE LOOP - For sewage and

sump applications when the discharge drains

naturally down and away from the pump, installing

an 8” to 10” positive loop right on the discharge port

will improve  the self priming feature. When you

stop pumping the loop traps some liquid against

the discharge valve improving the seal.

  Operation Guidelines

Union Ball Valve

Union Check Valve

 PVC Pipe Adapter

P-220A-03

Discharge  Loop

Page 6 Operation Guidelines

Содержание 220A Series












Отзывы: