background image

 

FCC Class B Certification 

This device complies with Part 15 of the FCC Rules. Operation is 
subject to the following conditions:

 

1.This device may not cause harmful interference, and 

2.This device must accept any interference received, including 

interference that may cause undesired operation. 

Warning!

 

This equipment has been tested and found to comply 

with the limits for a Class B digital device, pursuant to Part 15 of 
the FCC Rules. These limits are designed to provide reasonable 
protection against harmful interference in a residential installation. 
This equipment generates, uses and can radiate radio frequency 
energy and, if not installed and used in accordance with the 
instructions, may cause harmful interference to radio 
communications. However, there is no guarantee that interference 
will not occur in a particular installation. If this equipment does 
cause harmful interference to radio or television reception, which 
can be determined by turning the equipment off and on, the user is 
encouraged to try to correct the interference by one or more of the 
following measures: 

    • Reorient or relocate the receiving antenna. 

    • Increase the distance between the equipment and receiver. 

    • Connect the equipment into an outlet on a circuit different 

       from the one which the receiver is connected to. 

    • Consult the dealer or an experienced radio/TV technician for 

       help. 

You are cautioned that changes or modifications not expressly 
approved by the party responsible for compliance could void your 
authority to operate the equipment. 

Содержание ES-3116RE+
















Отзывы: