background image

5

Power Cable

Ground Cable

Auto Turn On (High level Input Only)

RCA Cables

• At least 4 gauge cable should be used for the ground connection to the amplifier.

• The amplifier ground should be connected directly to the chassis of the vehicle, to 

   bare metal.

• The cable length should be kept to an absolute minimum.

• It is not recommended that you connect the ground cable to the vehicles seatbelts  

   anchor point.

• At least 4 gauge cable should be used for the power connection to the amplifier.

• The power cable should be taken directly from the battery. Rubber grommets should be  

  used when passing through any bulkheads to prevent the cable from becoming chaffed 

  or cut.

• It is vital that a fuse / circuit breaker (of at least equal value to the one fitted in the 

  amplifier) is placed inline with the power cable and is no further than 18 inches away  

  from the battery.

• Please ensure that the fuse is not fitted until the entire installation procedure is complete.

• The EDGE amplifiers  feature an auto turn on circuit called Autosense.

• This circuit allows the amplifier to switch on and off without a remote turn on wire  

   when using high level input, for low level input (RCA) it will still be necessary to 

   connect the remote turn on wire from the headunit.

• When the connected source (headunit) is turned on the amplifier will turn on 

   automatically, after the connected source (headunit) is turned off the amplifier will  

   shut down.

• Depending on the model number of your amplifier and the number of speakers you 

   wish to power you will have to run either one or two or RCA cables from the source to 

   the amplifier.

• Please take extra care when running these cables from the source to the amplifier. 

   Ensure that they are placed away from all items that can generate any interference,

   wiring harnesses etc.

• It is recommended that the RCA cables should be run on opposite sides of the car 

   to  the previously installed power cables if possible, to avoid the cable picking up 

   interference.

Содержание DBX Series





















Отзывы: