WARNING
IMPROPER USE OF THIS HEATER COULD RESULT IN RISK OF FIRE, ELECTRIC SHOCK,
AND INJURY TO PERSONS
WARNING
ANY REQUIRED SERVICE OTHER THAN FILTER MAINTENANCE SHOULD ONLY BE
PERFORMED BY AN AUTHORIZED SERVICE REPRESENTATIVE AND ANY
OTHER REPAIRS ATTEMPTED BY ANYONE OTHER THAN AN AUTHORIZED
SERVICE REPRESENTATIVE WILL VOID THE WARRANTY.
FOR AUTHORIZED SERVICE, CALL 1-800-225-6595 OR VISIT WWW.EDENPURESERVICE.COM
WARNING
RISK OF ELECTRICAL SHOCK DO NOT OPEN
NO USER-SERVICEABLE PARTS INSIDE
READ ALL SAFETY INSTRUCTIONS BEFORE USING THE HEATER
1.
This heater’s grill is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Keep combustible materials
such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet (0.9m) from the front of the heater and keep
them away from the sides and the rear.
2. Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left
operating and unattended.
3.
Always unplug heater when not in use.
4.
Do not operate any heater with a damaged cord or plug, or after it has been dropped or damaged in any manner. In
such cases, return the heater to an authorized service facility for inspection/repair.
5.
Do not use the heater outdoors or on construction sites.
6.
The heater is not intended for use in bathrooms, laundry areas and similar indoor locations, areas with standing water,
a shower or swimming pool. Never place the heater where it may fall into a bathtub or other water container.
7.
Do not run the cord under carpeting. Do not cover the cord with throw rugs, runners, or similar coverings. Arrange the
cord away from traffic areas and where it will not be tripped over.
8.
To disconnect the heater, turn the unit off, then remove the plug from the outlet once it has stopped running.
9.
Do not plug the heater into any other cord-connected device such as a power strip, surge protector, multiple outlet
adapter, grounding adapter or outlet-type air fresheners. Plug into a 3-prong 120v 15amp or higher grounded circuit
receptacle only. Do not plug the heater into a loose-fitting or broken receptacle. The heater is for use on 120 volt outlets.
The cord has a plug as shown at “A” in Figure below.
10. Do not insert or allow foreign objects to enter any ventilation or exhaust opening, as this may cause an electric shock or
fire, or damage the heater.
11. To prevent a possible fire, do not block, or place anything in the front or rear of, the heater.
12. When performing filter maintenance, do not force the filter to dry using alternative methods. Doing so could damage
the filter.
13. Do not use in areas where gasoline, paint or flammable liquids are used or stored.
14. Some EdenPURE
®
heaters contain a button battery for the remote. If swallowed, it could cause severe injury or
death in just two hours. Seek medical attention immediately.
15. Use this heater only as described in the manual. Any other use not recommended by the manufacturer may cause fire,
electric shock or injury to persons and may void the warranty.
16. Manual restart maybe required if power to this unit is interrupted.
IMPORTANT SAFETY INSTRUCTIONS
GETTING STARTED
GROUNDING
PIN
COVER OF GROUNDED
OUTLET BOX
(A)
METAL SCREW
READ ALL INSTRUCTIONS BEFORE USING THE HEATER
1.
We recommend keeping the packaging for off-season storage and for any transportation needs.
2.
Find a level and unobstructed location to place the unpackaged heater.
3.
Do not plug in or run any appliances on the same circuit while the heater is running.
4.
Plug the power-cord directly into an unused, grounded receptacle.
5. FIRST TIME QUICK START UP - Push the POWER button to turn the unit on. “Factory Settings Restored” will appear on the
display upon initial use or when power has been lost for an extended period of time. Press NEXT to continue. The unit is
factory set on “Heat” mode at 72ºF. Press
s
or
t
to adjust the desired temperature.
IMPORTANT: If “Factory Settings Restored” is displayed as described above, the unit will require 5 to 10 minutes to acclimate to
the room and display an accurate room temperature. Feel free to use the unit during this time but realize that it will not properly
sense and react to the real room temperature for 5 to 10 minutes. If, after 5 to 10 minutes, the temperature is not the same as
your wall thermostat, use the “Temp Calibration” (described on the next page) to calibrate the unit.
6. Customize your Heater set up: Press SETTINGS
SETTINGS – the following options are found when pressing the SETTINGS button.
Set Time – used to set the correct day and time on the display of the unit. Setting the time is necessary for schedule or timer usage.
