ECS Mantis PV-28SV50-BN-1 Скачать руководство пользователя

Страница: 1 / 56

22618-12-0707

Page 1

INSTALLATION INSTRUCTIONS

AND

OWNER’S MANUAL

Mantis

Power Hu

midifier

Burners

Exhaust

Fan

Blower

Med

Low

Front

Rear

POWER-VENT

HIGH-EFFICIENCY

FIREPLACE WITH

BAY WINDOW

MODELS

PV-28SV50-(BN,BP)-1

PV-28SV55-(CN,CP,GN,GP)-1

EFFECTIVE DATE

MAY 2007

WARNING: If not installed, operated and main-

tained in accordance with the manufacturer’s in-

structions, this product could expose you to sub-

stances in fuel or from fuel combustion which can

cause death or serious illness.

Installer: Leave this manual with the

appliance.

Consumer: Retain this manual for future

reference.

— Do not store or use gasoline or other ﬂamma-

ble vapors and liquids in the vicinity of this or

any other appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not

use any phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas suppli-

er’s instructions.

• If you cannot reach your gas supplier, call

the ﬁre department.

— Installation and service must be performed

by a qualiﬁed installer, service agency or the

gas supplier.

WARNING: If the information in these in-

structions are not followed exactly, a ﬁre or ex-

plosion may result causing property damage,

personal injury or loss of life.

This appliance may be installed in an aftermarket,

permanently located, manufactured home (USA

only) or mobile home, where not prohibited by

state or local codes.
This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is

not convertible for use with other gases, unless a

certiﬁed kit is used.

™

This appliance is NOT to be installed in Canada.

Содержание Mantis PV-28SV50-BN-1

























































Результаты поиска

Содержание Mantis PV-28SV50-BN-1

Отзывы:

Похожие инструкции для Mantis PV-28SV50-BN-1

Бренды по названию

Популярные бренды

ECS Mantis PV-28SV50-BN-1, Инструкция по установке и руководство пользователя

Результаты поиска

Содержание Mantis PV-28SV50-BN-1

Отзывы:

Похожие инструкции для Mantis PV-28SV50-BN-1

Бренды по названию

Популярные бренды