ECR International Dunkirk DMG-240 Скачать руководство пользователя

Страница: 78 / 86

13 - TROUBLE SHOOTING

Troubleshooting Chart 6

LP Installation?

YES

Is gas shutoff valve fully

open?

YES

Open Gas shutoff valve.

E36

- Burner Flame Loss

LP Conversion kit installed?

YES

Has all air been purged

from gas line?

YES

Replace

Spark

Generator

Install LP

Conversion Kit

Check all wires including

igniter and gas valve are

connected and tight.

YES

Refer to section 6 of IOM and correct

vent terminations

Connect all wires assure secure fit.

Are ground wires

attached? Is boiler

properly grounded?

YES

Provide proper ground.

Purge all air from gas line.

Check gas inlet pressure at least

equals rating plate requirements

YES

Check gas line for obstructions

Check venting. Is

exhaust gas recirculating

to the air intake?

YES

Clean or

Replace Igniter

Clear Vent

Obstruction

Remove igniter and

inspect. Is there damage

or contamination?

YES

Restart boiler. Go to display

and check flame current. Is

there at least 3 mA?

YES

Check venting for obstruction

and/or wind effects

YES

Remove burner and inspect. Any

sign of damage to burner surface?

YES

Replace

Burner

Check interior of heat exchanger for

debris or signs of blockage

YES

Replace gas

valve

Clean Heat

Exchanger

PN 240011656 REV. K [11/01/2020]

Содержание Dunkirk DMG-240























































































Результаты поиска

Содержание Dunkirk DMG-240

Отзывы:

Похожие инструкции для Dunkirk DMG-240

Бренды по названию

Популярные бренды

ECR International Dunkirk DMG-240, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Dunkirk DMG-240

Отзывы:

Похожие инструкции для Dunkirk DMG-240

Бренды по названию

Популярные бренды