ECR International Dunkirk DMG-240 Скачать руководство пользователя

Страница: 53 / 86

9.13 User Level Parameters

Parameters

can be adjusted by end user to meet

heating system and DHW comfort needs.

Modification of factory settings may be detrimental to

operation of the boiler.

• Press the two Menu buttons

simultaneously and

then (+) button until

symbol flashes on the menu

bar.

• Select the user menu using

button, (

) button

is displayed with "

" flashing.

• Press

button a second time, the central heating

supply temperature value appears and flashes, e.g.

170°F.

• Change the value by pressing (

) button or (

) button.

In this example using (

) to (

140°F

•

Confirm the value with

button, (

) is displayed

with "

" flashing.

• Press

button 2 times to return to current

operating mode.

9 - START UP PROCEDURE

9.14 Installer Level Parameters

Parameters

P17

(error code history) must only be

modified by a qualified installer.

To prevent unwanted settings, some parameter settings can

only be changed after special access code

0012

is entered.

Modification of factory settings may be detrimental to

operation of the boiler.

• Press the two Menu buttons

simultaneously and

then (+) button until the symbol

flashes on the

menu bar.

• Select the INSTALLER menu using the

button.

CODE

" appears on the display.

• Use (-) or (+) button to input the installer code "

0012

•

Confirm using

button, "

" is displayed with "

flashing.

• Press

button a second time, the value will appear

and flashes, for example [80°C (176°F)].

• Change the value by pressing the [

] or [

] button. [In

this example using [

] button to change the value to 60

ºC (140 °F).]

•

Confirm the value with the

button, “

” is

displayed with 1 flashing. Button, “P1” is displayed

with 1 flashing. If necessary, set other parameters by

selecting them using the (

) or (

) button.

• Press

button 2 times to return to current

operating mode.

FIGURE 9-9 - User Level Parameters

FIGURE 9-10 - Installer Level Parameters

PN 240011656 REV. K [11/01/2020]

Содержание Dunkirk DMG-240























































































Результаты поиска

Содержание Dunkirk DMG-240

Отзывы:

Похожие инструкции для Dunkirk DMG-240

Бренды по названию

Популярные бренды

ECR International Dunkirk DMG-240, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Dunkirk DMG-240

Отзывы:

Похожие инструкции для Dunkirk DMG-240

Бренды по названию

Популярные бренды