ECR International Dunkirk DMG-240 Скачать руководство пользователя

Страница: 76 / 86

13 - TROUBLE SHOOTING

Is return line warmer than

supply line?

YES

Check wire plugs are

securely connected to

sensors.

YES

Error Code is

accurate.

Correct system

piping.

Assure wire harness plugs

are securely connected to

sensors

Check water pressure. Is water

pressure at least 15 psig?

YES

Troubleshooting Chart 4

Refer to temperature

sensor chart

YES

Replace

control board

Check both sensors are

properly inserted into pipe

lines.

YES

Repair sensor insertion

into pipe lines

E10, E11

- Temperature Difference Between

Supply and Return Too Great

E35 -

Supply and Return Sensors Reversed

Onboard pump operation

properly?

YES

Replace

pump

Possible air

in system.

De-aerate

Are any water valves

partially closed?

YES

Open all

valves

Check wire harness against

wiring diagram. Are Supply

sensor wires green and

Return Sensor wires red?

YES

Wire connections are

reversed. Correct

wiring connections.

Replace

sensor

PN 240011656 REV. K [11/01/2020]

Содержание Dunkirk DMG-240























































































Результаты поиска

Содержание Dunkirk DMG-240

Отзывы:

Похожие инструкции для Dunkirk DMG-240

Бренды по названию

Популярные бренды

ECR International Dunkirk DMG-240, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Dunkirk DMG-240

Отзывы:

Похожие инструкции для Dunkirk DMG-240

Бренды по названию

Популярные бренды