background image

9

ULTRAVIOLET (UV) LAMP AND SLEEVE ASSEMBLY

1

1.    Locate canister number 4 (shown on previous page). 

With the 

plastic cover

 removed, remove the threaded 

retainer

 on the top of the ultraviolet (UV) canister. (See 

figure 1 & 2).

2

2.  Open the carton containing the 

UV lamp

 and  

the 

quartz sleeve

. Remove the 

quartz sleeve

 

from its packing. (Be sure not to remove UV bulb  
from packing yet). 

5

5.  Place the threaded 

retainer

 over the top of the 

sleeve

 

and gently tighten the cap until it is snug and the top of 
the 

sleeve

 is properly seated in the cap. Do not over-

tighten as the 

sleeve

 may break (See figure 4).

6

6.  Check the seat at the top of the 

sleeve

 by 

reaching into the middle of the 

retainer

 and 

rubbing a finger along the inside of the glass. 
There should be a slight gap between the glass 
and the 

cap

. If an uneven gap is present, do 

not attempt to tighten the 

cap

 further as the 

sleeve 

will break. The uneven gap indicates 

that the 

sleeve

 is misaligned. STOP and repeat 

step #3 taking care to insure proper seating and 
alignment of the sleeve.

7

7.  Remove the 

UV lamp

 from the packing and clean 

thoroughly with rubbing alcohol to remove all traces 
of oil and grease. Be careful not to touch the glass 

lamp

 area with your fingers as this will leave oils on 

the 

lamp

, causing the 

lamp

 to fail prematurely. 

8

8.  Carefully slide the 

UV lamp

 through the 

retainer

 and into the 

quartz sleeve

 making 

sure that the lamp prongs are at the top 
(See figure 5).

9

9.  Plug the ballast into the top of the 

UV lamp

 

(See figure 6).

10

10. Place the 

plastic cover

 over the 

retainer

 to 

protect the top to the 

UV lamp

. The 

lamp

 should 

be seated low enough in the 

sleeve

 so that when 

the 

plastic cover

 is in place, there is clearance 

between it and the cabinet top (See figure 7). 
Plug ballast into properly grounded 110-120 Volt 
household receptacle.

3

3.  The 

quartz sleeve

 resembles a large test tube. 

Remove the sleeve from the packing and place it 
into the top of the UV canister and carefully lower it 
into place. Be sure the 

sleeve

 is straight and slides 

fully into the receiving tube at the bottom of the 
canister. The sleeve will be fitted with a black O-ring 
and a plastic washer near the top. These should be 
positioned about 1/2 inch from the top of the tube. 
All water should be removed from the canister before 
proceeding with this step (See figure 3).

4

4.  Check that the bottom of the 

sleeve

 is seated 

properly by gently depressing the top edge 
of the sleeve with a finger. The sleeve should 
bounce on the spring located in the receiving 
tube. If it does not bounce the tube is misaligned 
and must be re-seated BEFORE proceeding.  
Apply a very thin coat of unscented petroleum 
jelly to the top rim of the sleeve. Be careful not 
to get any of the jelly on the inside of the sleeve.

figure 1

figure 2

figure 7

figure 6

figure 5

figure 4

figure 3

WARNING: THE SLEEVE IS FRAGILE. ROUGH HANDLING OR MISALIGNMENT WILL CAUSE IT TO BREAK.

CAUTION - SHOCK HAZARD:  BE SURE UNIT IS PROPERLY GROUNDED (SEE PAGE 7) AND AREA  

IS FREE OF STANDING WATER BEFORE PLUGGING UNIT INTO RECEPTACLE.

1/2”

Содержание SpringHouse

















Отзывы: