background image

6

INSTALLATION NOTES

PRELIMINARY MEASURES

1

1.  Place the unit in the location of installation.

2

2.  Remove top cover by loosening thumb screws and 

pulling upward in a straight motion. Set the top 
aside. Remove side panel which is attached with 
hook & loop tape. Grasping the edges on both 
ends, pull outward tipping top toward you.  
You may remove both sides for best access if  
space allows.

3

3.  Carefully remove the carton located in the base of 

the unit. This carton contains the ultraviolet light 
and quartz sleeve.

4

4.   Carefully unwrap the valve assembly and 

connect it to the unit using the two unions as 
shown in the accompanying diagram. Make sure 
all unions are snug and free of “play.”

5

5.    Plumb the unit into the water service line using the 

unions provided paying close attention to the inlet 
and outlet.

 /

"1//

GENERAL 
PRECAUTIONS:

•  Installation must be done 

by a qualified plumber in 
accordance with local codes. 
Failure to do so can result 
in damage not covered by 
your SpringHouse warranty. 
Installation by a licensed 
plumber is recommended.

•  SpringHouse can be installed 

outdoors but must be 
protected from freezing, 
excessive heat and direct 
sunlight. Failure to do so can 
result in component failure, 
water leakage, and/or  
property damage and will  
void the warranty.

•  Install on cold water  

lines only. 

•  Install after the  

pressure regulator.

•  Install after any pressure 

tanks or other water treatment 
equipment such as softeners.

•  Flow must be in the direction 

indicated on the canister tops.

•  When installing unit, be sure 

to position it for easy access 
to the filter canisters for 
maintenance purposes.

•  Unit must be located  

within 6 feet of a  
110v - 120v gfci outlet.

•  Inlet and outlet plumbing  

1 inch.

•  Maximum supply pressure  

250 psi. 

•  Operating temperature range 

of 35-100 degrees Fahrenheit.

•  Rated service flow of up to 

8 g.p.m. The use of reducers 
and/or excessive fittings can 
result in a decreased flow 
rate and is not recommended. 
Household water pressures  
of less than 40 psi will result 
in a noticeable reduction in 
flow rate.

Содержание SpringHouse

















Отзывы: