background image

Page 2

OMNI by EconoHeat

Table of Contents

Precautions ................................................................................... Page 3

Important Notice ......................................................................... Page 4

Speciications ............................................................................... Page 5

Installation Procedures .............................................................. Page 6

Stack Installation .......................................................................... Page 7

Oil Supply Tubing ......................................................................... Page 7

Wiring .............................................................................................. Page 8

Ducting ........................................................................................... Page 8

Oil Burner ....................................................................................... Page 9

Oil Burner Technology .............................................................. Page 11

Initial Start Procedure ............................................................... Page 13

Maintenance Schedule .......................................................... Page 14

Figures 9 – 14 .............................................................................. Page 15

Troubleshooting ......................................................................... Page 18

OWH-150 Fifteen Year Limited Warranty .............................. Page 19

Warranty Card ........................................................................... Page 20

Содержание OMNI OWH-150





















Отзывы: