Ecolawn ECO250 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 19

Ecolawn ECO250 Скачать руководство пользователя страница 14

www.ecolawnapplicator.com

Turf Pros #1 Top dresser

P a g e

12 | 17

Symptom: The spreader's hopper is full. The conveyor has been activated by pulling the conveyor

activation lever back, but the conveyor belt is not turning even though the stretch rod has been

adjusted properly and the conveyor drive roller is turning.

Solution: Adjust the tension of the conveyor belt rollers on each side, 1/2 a turn at a time, to increase the

tension on the conveyor belt, as follows: do this on both sides of the unit equally.

1.Loosen the three (yellow) nuts.

2.Tighten the horizontal (red) bolt to push the conveyor

belt roller forward about 1/2 turn

3.Tighten the three (yellow) nuts to hold the conveyor

belt in place.

4.Repeat the same procedure on the other side, making

sure the adjustments to both sides

Symptom: The spreader does not move forward, or does so only with difficulty.

Solution: An adjustment to the tension of the activation arm of the Self-Propel Handle may be necessary:

1.Loosen the (yellow) jam nut to release the tension.

2.Turn the (green) adjustment collar clockwise to

increase pressure, or counter clockwise to reduce

pressure.

3.Tighten the (yellow) jam nut to maintain the desired

pressure.

«
...
12
13
14
15
16
...
»

Содержание ECO250




















Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды