ECO-MATIC ESC 16 Скачать руководство пользователя

Страница: 81 / 128

Step 1

– Place transformer over the locating

screw.

Step 5

– With a soldering iron & solder

sucker or solder wick remove the 3

transformer wires. The transformer

wires are the red, black & white

wires on the top left corner of the

PCB. When the metal has cooled

remove the transformer wires.

Note the placement of the wires

on the PCB so as to enable easier

reassembly.

Assembly

Step 2

– Place heat dispersion disk over the

transformer with the shiny metallic

side face up. Place flat washer

in place over the locating screw,

tighten the transformer nut using an

8mm spanner.

Step 6

– Remove the nut on the top of

the transformer with an 8mm

spanner then lift off the black

heat dispersion disk which when

removed allows for the transformer

to be lifted out of the chlorinator.

When removing heat dispersion

disk also remove the flat washer

located beneath the nut.

BLUE
BROWN

Содержание ESC 16

































































































































Результаты поиска

Содержание ESC 16

Отзывы:

Похожие инструкции для ESC 16

Бренды по названию

Популярные бренды

ECO-MATIC ESC 16, Руководство по эксплуатации

Результаты поиска

Содержание ESC 16

Отзывы:

Похожие инструкции для ESC 16

Бренды по названию

Популярные бренды