ECO-MATIC ESC 16 Скачать руководство пользователя

Страница: 31 / 128

Step 2

– Place cell cord assembly into

position & secure with the holding

plate using a Phillips head

screwdriver (two point).

Step 1

– With a soldering iron & unleaded solder reattach the cell cables & gas sensor cable to

the PCB.

ESC 16 – 24 110V & 220V:

The order for soldering the cell cables back onto the PCB

from left to right is 1) black, 2) black, 3) dark blue. The gas sensor is the dark blue

cable which should be soldered onto the position on the PCB marked Gas.

ESC 36 – 48 220V:

The order for soldering the cell cables back onto the PCB from left to right

is: 1) black cell cable, 2) light blue transformer cable & black cell cable in the same slot, 3) dark

blue cell cable which goes in the slot marked Gas.

Assembly

Step 3

– Replace any cable ties that were

removed then replace the protective

covering on the PCB with a Phillips

head screwdriver (one point).

1. BLACK

2. BLACK

2. LIGHT BLUE & BLACK

3. DARK BLUE

Содержание ESC 16

































































































































Результаты поиска

Содержание ESC 16

Отзывы:

Похожие инструкции для ESC 16

Бренды по названию

Популярные бренды

ECO-MATIC ESC 16, Руководство по эксплуатации

Результаты поиска

Содержание ESC 16

Отзывы:

Похожие инструкции для ESC 16

Бренды по названию

Популярные бренды