background image

7

2. A quick press and release of the button at this point will allow you to select 

between test modes. Pressing and releasing the test button scrolls through 

the LED indicators. When the red LED is blinking, go to step 3. 

3. 

Press and hold the test button again for 6 seconds to select Walk Test 

mode. The red LED will begin blinking when motion is detected. The test 

will run for a duration of 100 seconds. You may quit the test at any time by 

pressing the test button for 10 seconds.

Sensitivity Adjust Mode:

 

The sensitivity feature allows the installer to adjust 

the sensitivity level. False occupancy states caused by other elements can be 

reduced by reducing the sensitivity level. The default setting is max. sensitivity. 

To enter sensitivity adjust mode, press and hold the Test button for 6 seconds. 

The green LED will begin to blink.

1. 

A quick press and release of the button at this point will allow you to 

select between test modes. Pressing and releasing the test button scrolls 

through the LED indicators. When the red and amber

 

LEDs are blinking 

simultaneously, go to step 2. 

2. Press and hold the test button again for 6 seconds to select PIR sensitivity 

adjust mode. One of the LEDs will begin blinking based on the selected 

settings, see the 

Sensitivity Adjust Table

.

3. A

 press and release of the button will allow you to scroll through the 

settings as shown in the sensitivity adjust table on page 7.

SENSITIVITY ADJUST TABLE

Setting

Indication

High

Green LED blinking

Medium

Amber LED blinking

Low

Red LED blinking

NOTE:  The  low  sensitivity  setting  is  used  as  the  base  line  for  the  lens  detection  ray 

diagrams found on the data-sheet.

4. To select a setting press and hold the test button for 10 seconds when the 

desired LED is blinking. To exit without saving, allow the test to time-out in 

60 seconds.

Installing Wireless Devices

Careful planning is needed when locating the receivers and transmitters based 

on the construction materials in the space and possibility of tenant’s furniture 

disrupting the transmissions. 

The  occupancy  sensor  should  be  installed  in  the  space  where  the  receiver  is 

mounted and connected to the occupancy control equipment. The signal will 

travel through some material barriers. 
Refer  to  the  tables  on  the  next  page  for  range  considerations  with  building 

materials that reduce the radio signal power. 

Содержание RVS-A-xW









Отзывы: