background image

G

RASS

 T

RIMMER

/B

RUSH

 C

UTTER

O

PERATOR

'

S

 M

ANUAL

15

NOTE
In case of Emergency, pull up on the Quick Release Collar to
disconnect the trimmer from the harness.

FUEL

Fuel Requirements

Gasoline - Use 89 Octane [R+M/2] (mid grade or higher) gasoline known
to be good quality. Gasoline may contain up to 15% MTBE (methyl
tertiary-butyl ether). Gasohol containing methyl (wood) alcohol is NOT
approved.

Two Stroke Oil - A two-stroke engine oil meeting ISO-L-EGD (ISO/CD
13738) and J.A.S.O. FC Standards must be used. Echo brand premium
Power Blend 

TM

 Universal 2-Stroke Oil meets these standards. Engine

problems due to inadequate lubrication caused by failure to use an ISO-
L-EGD and J.A.S.O. FC certified oil, such as Echo premium Power Blend

TM

, will void the two-stroke engine warranty.  (Emission related parts

only are covered for two years, regardless of two-stroke oil used, per
the statement listed in the Emission Defect Warranty Explanation.)

IMPORTANT
Echo premium Power Blend 

TM

 Universal 2-Stroke Oil may be mixed

at 50:1 ratio for application in all Echo engines sold in the past
regardless of ratio specified in those manuals.

Handling Fuel

WARNING  

 DANGER

Fuel is VERY flammable. Use extreme care when mixing, storing or
handling or serious personal injury may result.
• Use an approved fuel container.
• DO NOT smoke near fuel.
• DO NOT allow flames or sparks near fuel.
• Fuel tanks/cans may be under pressure. Always loosen fuel caps

slowly allowing pressure to equalize.

• NEVER refuel a unit when the engine is HOT or RUNNING!
• DO NOT fill fuel tanks indoors. ALWAYS fill fuel tanks outdoors

over bare ground.

• DO NOT overfill fuel tank.  Wipe up spills immediately.
• Securely tighten fuel tank cap and close fuel container after

refueling.

• Inspect for fuel leakage. If fuel leakage is found, do not start or

operate unit until leakage is repaired.

• Move at least 3m (10 ft.) from refueling location before starting

the engine.

o

i

t

a

R

1

:

0

5

-

x

i

M

li

O

o

t

l

e

u

F

.

S

.

U

C

I

R

T

E

M

S

A

G

L

I

O

S

A

G

L

I

O

s

n

o

ll

a

G

.

z

o

.l

F

r

e

ti

L

.

c

c

1

2
5

6

.

2

2

.

5

3

1

4

8

0

2

0

8

0

6

1

0

0

4

Содержание SRM-251U

































Отзывы: