background image

28

Specifications

Specifications

These specifications are subject to change without notice.

SRM-236ES

L

U

External dimensions:

Length × Width × Height

mm

1770 × 340 × 330

1775 × 710 × 395

Mass:

Unit without cutting attachment and shield (ISO 11806)
Unit with fuel, specified cutting attachment, shield and 

harness

kg
kg

4.9
6.2

5.6
7.2

Volume:

  Fuel tank

L

0.44

Cutting attachment:

Nylon line cutting head
Line diameter
Line length
Thread
Specified blade diameter
Specified blade thickness
Number of cutting teeth
Blade centre hole diameter
Blade rotational speed at maximum allowable engine 

speed

mm
m

mm
mm

mm

r/min

F4
3.0
2 ×1 line
Left-handed M10×1.25

230
3.0
3
25.4

8235

Gear ratio:

 Gear ratio and lubrication

1.36 reduction and good quality lithium grease

Rotational direction of output shaft seen from above:

Anticlockwise

Engine:

Type

Air cooled 2-stroke single cylinder

Engine displacement
Maximum shaft brake power, measured in accordance 

with ISO 8893

Recommended engine idling speed
Engine speed at maximum engine power

mL (cm

3

)

kW
r/min
r/min

21.2

0.71
3000
8000

Recommended maximum engine speed (With STD at-

tachment installed)

r/min

9500

11200

Carburettor
Ignition
Spark plug
Starter
Clutch

Diaphragm type
Flywheel magneto - CDI system
NGK BPMR8Y
Recoil starter
Automatic centrifugal clutch

Fuel:

Oil

Ratio

Regular grade petrol. Minimum 89 Octane unleaded
petrol is recommended. Do not use fuel containing me-
thyl alcohol or more than 10 % of ethyl alcohol.
Two stroke, air-cooled engine oil. ISO-L-EGD Standard
(ISO/CD 13738), JASO FC,FD grade and ECHO Premi-
um 50 : 1 oil.
50 : 1 (

2%

)

Fuel consumption at maximum engine power
Specific fuel consumption at maximum engine power

L/h
g/(kW•h)

0.45
469

Vibration levels:

 (ISO 22867)a

hv,eq

m/s

2

m/s

2

Front handle 4.6
Rear handle 4.1

Right handle 4.1
Left handle 3.7

Sound pressure level:

 (ISO 22868) L

pAeq

dB(A)

92.9

93.0

Guaranteed sound power level:

(ISO 22868) L

WA

dB(A)

107

108

Содержание SRM-236ES

































Отзывы: