background image

3

For safe use of your product

For safe use of your product

Important information

 WARNING

Please ensure that you read the operator's manual before using your product.

About your operator's manual





This manual contains necessary information about the assembly, operation, and maintenance of your product. 
Please read it carefully and absorb its contents.



Always keep your manual in a place where it is readily accessible.



If you have lost your manual or it is damaged and no longer readable, please purchase a new one from your dealer.



The units used in this manual are SI units (International System of Units). Figures in parentheses are reference val-
ues, and there may be a slight conversion error in some cases.

Failure to do so could lead to an accident or serious injury.

Intended use of this product



This product is lightweight, high-performance, petrol engined unit designed for weed control, grass trimming and 
brush cutting in areas difficult to control by any other means.



Do not use this unit for any purpose other than aforementioned.



The content of this manual may be changed without notice for the purpose of upgrades to the product. Some of the 
illustrations used may differ from the product itself in order to make the explanations clearer.



Please consult your dealer if anything is unclear or of concern.

Failure to do so could lead to an accident or serious injury.

Do not modify the product



You must not modify the product.

To do so could lead to an accident or serious injury. Any malfunction resulting from a modification to the product will not be 
covered by the manufacturer's warranty.

Do not use the product unless it has been checked and maintained



You must not use the product unless it has been checked and maintained. Always ensure that the product is checked 
and maintained on a regular basis.

Failure to do so could lead to an accident or serious injury.

Loaning or assigning your product



When loaning your product to another party, ensure that the person borrowing the product receives the operator's 
manual along with it.



If you assign your product to another party, please enclose the operator's manual with the product when handing it 
over.

Failure to do so could lead to an accident or serious injury.

Users of the product



The product should not be used by:

Œ

people who are tired

Œ

people who have taken alcohol

Œ

people who are on medication

Œ

people who are pregnant

Œ

people who are in poor physical condition

Œ

people who have not read the operator's manual

Œ

children



Keep in mind that the operator or user is responsible for accidents or hazards occurring to other people or their prop-
erty.

Failure to observe these instructions could lead to an accident.

Содержание SRM-236ES

































Отзывы: