manualshive.com logo in svg

Echo SRM-22GES, Руководство оператора

Поделиться
Скачать
Echo SRM-22GES Скачать руководство пользователя страница 22

22

SRM-22GES

SRM-22GES

Mass

 :

unit without cutting attachment, empty tank

kg

4.63

unit with specified cutting attachment, empty tank

kg

4.84

unit with specified cutting attachment, full tank

kg

5.17

Volume

 :

fuel tank

L

0.44

Cutting attachment

 :

nylon line head

G138

line diameter

mm

3.0

line length

m

2 

×

 1 line

thread

Left-handed M10 

×

 1.25

Gear ratio

 :

gear ratio and lubrication

1.4 reduction and good quality lithium grease

Rotational direction of output shaft seen

from above

 :

Anticlockwise

External dimensions

 :

length

mm

1,785

width

mm

210

height

mm

360

Engine

 :

type

Air cooled two stroke single cylinder

engine displacement

mL(cm

3

)

21.2

maximum shaft brake power, measured in

accordance with ISO 8893

kW

0.67

engine speed at maximum engine power

r/min

6,500

recommended maximum engine speed

r/min

8,400

output shaft speed

r/min

-

recommended engine idling speed

r/min

3,000

engine speed at beginning of clutch engagement

r/min

3,900

carburettor

Diaphragm type

ignition

Flywheel magneto - CDI system

spark plug

NGK BPMR7A

starter

Recoil starter (

“ES” START

)

clutch

Automatic centrifugal clutch

Fuel

 :

Regular grade petrol. Minimum 89 Octane unleaded
petrol is recommended. Do not use fuel containing
methyl alcohol or more than 10 % of ethyl alcohol.

oil

Two stroke, air-cooled engine oil. 50 : 1 for ISO-L-
EGD Standard (ISO/CD 13738), JASO FC grade
and ECHO Premium 50 : 1 oil.

ratio

50 : 1 (

2 %

)

fuel consumption at maximum engine power

L/h

0.62

specified fuel consumption at maximum

engine power

g/(kW

•

h) 685

Sound pressure level

 : (ISO 22868) LpAav=

dB(A)

94.2

Sound power level

 : (ISO 22868) LwAav=

dB(A)

101

Vibration levels

 : (ISO 22867)

idling

m/s

2

4.0

racing

m/s

2

7.5

SPECIFICATIONS

Specifications, descriptions and illustrative material in this
literature are as accurate as known at the time of publication,
but are subject to change without notice.

Illustrations may include optional equipment and
accessories, and may not include all standard equipment.

Содержание SRM-22GES

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды