background image

G

rass

 T

rimmer

/B

rush

 C

uTTer

O

peraTOr

'

s

 m

anual

17

startIng

 

warm

 

engIne

The starting procedure is the same as Cold Start except DO NOT close 

the choke, and do not hold throttle trigger fully depressed.

  WARNING 

The attachment should not move at idle, otherwise serious per-

sonal injury may result.

NOTE

If attachment moves, readjust carburetor according to “Carburetor 

Adjustment” instructions in this manual or see your ECHO Dealer.

1. 

Stop Switch

 

Move stop switch button  (A) forward away from the STOP posi-

tion.

2. 

Purge Bulb

 

Pump purge bulb (C) until fuel is visible in the "Clear" fuel return 

line.

3. 

Recoil Starter 

 

 

 

  

 

 

Lay the unit on a flat area and keep movable attachment parts clear 

of all obstacles. Rapidly pull the recoil starter handle (D) until the 

engine fires.

NOTE

If engine does not start after 5 pulls, use Cold Start Procedure.

stoppIng

 

engIne

1.

 

Release Throttle.

  

 

Allow engine to return to idle before shutting off engine.

2.

 

Stop Switch

 

 

Move stop switch button (A) backward to STOP position.

  WARNING 

If engine does not stop when stop switch is moved to STOP posi-

tion, close choke - COLD START position - to stall engine. Have 

your ECHO dealer repair stop switch before using trimmer again.

A

A

C

D

Содержание SRM-225 - 09-10





































Отзывы: