Echo SRM-2100 - PARTS CATALOG SERIAL NUMBER 001001 THRU 159490 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 37

background image

16

G

E

D

F

U

-

HANDLE

INSTALLATION

Tools Required: 8mm x 10mm Open End Wrench, Slotted Screwdriver,
(3mm Hex Wrench SRM-2100 only.)

Parts Required: U-Handle Kit. (SRM-2100) P/N 35130454130

NOTE
On model SRM-2110 use Steps 1, 10, 11, and 13 - 17 only.

1. Close choke and remove air filter cover.

2. Disconnect ignition stop leads (C).

3. Remove inner throttle linkage from carburetor swivel (B).

4. Loosen nut (A) and remove throttle linkage from bracket.

5. Loosen two (2) bolts (D) and pull drive shaft assembly from clutch

case.

6. Loosen two (2) rear handle screws (E) and pull rear handle (F) from

the drive shaft assembly.

7. Loosen four (4) screws and remove front handle (G).

8. Position Lower U-Handle Bracket (H) 400mm (15-3/4 in.) from

engine end of drive shaft. Secure with three (3) 5mm x 30mm
bolts.

9. Install harness hook (included with Blade Conversion Kit) for

blade use. Position 220 mm (8-5/8 in.) from engine end of drive
shaft assembly. DO NOT tighten at this time.

10. Install upper U-Handle and bracket on lower bracket and secure

with one (1) 8mm x 55mm bolt (J) and large circular washer.

J

400 mm (15-3/4 in.)

220 mm

(8-21/32 in.)

ENGINE

END

H

«
...
14
15
16
17
18
...
»

Содержание SRM-2100 - PARTS CATALOG SERIAL NUMBER 001001 THRU 159490






































Отзывы:

Нет отзывов

Похожие инструкции для SRM-2100 - PARTS CATALOG SERIAL NUMBER 001001 THRU 159490

Бренд: Tally Dascom Страницы: 20

Бренд: KEENCUT Страницы: 9

Бренд: UCHIDA Страницы: 61

Бренд: IDEAL Страницы: 48

Бренд: Spedo Страницы: 55

Бренд: Shoprider Страницы: 20

Бренд: Chicago Pneumatic Страницы: 36

Бренд: Chocolate World Страницы: 17

Бренд: Mac Afric Страницы: 21

Бренд: Martin Yale Industries Страницы: 4

Бренд: Ryobi Страницы: 140

Бренд: UZIN Страницы: 16

Бренд: Ryobi Страницы: 20

Luna Machinery KD 310

Бренд: YILMAZ Страницы: 28

Бренд: Raider Страницы: 51

Бренд: Zenoah Страницы: 16

Бренд: PAPILLON Страницы: 44

Бренд: Tanaka Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды