Echo SRM-2100 - PARTS CATALOG SERIAL NUMBER 001001 THRU 159490 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 37

background image

G

RASS

T

RIMMER

/B

RUSH

C

UTTER

O

PERATOR

'

S

M

ANUAL

15

THROTTLE

LINKAGE

AND

IGNITION

LEADS

Tools Required: 8mm x 10mm open end wrench (all models), 3mm Allen
Wrench.

1. Close choke and remove air filter cover.

2. Loosen nut (A) and place threaded end of throttle linkage in

bracket slot. Finger tighten nut (A).

3. Place inner cable in slot of carburetor swivel (B) and tighten

nut (A).

4. Check throttle for freedom of movement and make sure it returns

to idle position. If the throttle linkage does not allow the carbure-
tor throttle plate (C) to return to idle against idle screw (D),loosen
linkage nuts; turn throttle linkage nut (A) counter clock

wise

until throttle plate (C) just rests against idle screw (D). Hold
linkage nut (A) from turning and tighten other linkage nut.

5. Connect ignition leads (C). SRM-2100 has one connector

terminal pair and one ring terminal which attaches under fan
terminal screw (C).

6. Install air filter and cover.

FRONT

HANDLE

INSTALLATION

Tools Required: Screwdriver.

Parts Required: Front Handle, Handle Support, Four (4) 5mm x 35mm
screws with captivated washers, four (4) 5mm nuts.

1.

Position front handle for comfortable operation and secure screws.

«
...
13
14
15
16
17
...
»

Содержание SRM-2100 - PARTS CATALOG SERIAL NUMBER 001001 THRU 159490






































Отзывы:

Нет отзывов

Похожие инструкции для SRM-2100 - PARTS CATALOG SERIAL NUMBER 001001 THRU 159490

Бренд: Shindaiwa Страницы: 40

Бренд: ARCBRO Страницы: 28

Бренд: 3D Nord Страницы: 9

Бренд: SIZZIX Страницы: 36

Бренд: TechnoVert Страницы: 44

Бренд: START International Страницы: 17

WAZER Main Unit

Бренд: Wazer Страницы: 69

KBC-2600 SERIES

Бренд: SMC Networks Страницы: 10

Бренд: Far Tools Страницы: 45

Бренд: Zenoah Страницы: 32

KZ-4000MT-PRO-2S

Бренд: Kasei Страницы: 118

Бренд: Zenoah Страницы: 8

Бренд: RASOR Страницы: 15

SUPER SPEED 1000200

Бренд: KENTMASTER Страницы: 27

Бренд: canty Страницы: 4

Бренд: Pattfield Ergo Tools Страницы: 90

Бренд: Bush Hog Страницы: 1

Бренд: Gardeo Страницы: 154

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды