Echo shindaiwa CS-501SX Скачать руководство пользователя страница 66

Страница: 66 / 80

REAR HANDLE AND CONTROL SYSTEM

CS-501SX, CS-501SXH

501sx

9-3-1 Inspecting heated handle

Inspecting stator assembly

1. Remove air cleaner cover (A), air fi lter and han-
dle cover (B).

2. Disconnect stator lead coupler (C).

NOTE:

If it is not clear which is stator lead coupler

(C), remove carburetor and carburetor elbow, and
check where the lead is connected to.

3. Connect one probe of ohm-meter or multi-meter
to stator lead (D) as shown.

4. Connect the other probe to heater switch lever (E)
or a clean ground as shown.

5. Tester should show that the circuit is in conduct-
ing state.

6. If stator assembly is defective, replace with a
new one (Refer to 9-3-2 “Replacing stator assem-
bly”).

Inspecting front handle heater

1. Disconnect stator lead coupler (A) and rear han-
dle heater coupler (B).

2. Connect one probe of ohm-meter or multi-meter
to one lead of front handle heater (C) as shown.

3. Connect the other probe to other lead of front
handle heater (D) as shown.

4. Tester should show that the circuit is in conduct-
ing state.

5. If front handle heater is defective, replace with a
new one.

Содержание shindaiwa CS-501SX
















































































Результаты поиска

Содержание shindaiwa CS-501SX

Отзывы:

Похожие инструкции для shindaiwa CS-501SX

Бренды по названию

Популярные бренды

Echo shindaiwa CS-501SX, Руководство по обслуживанию

Результаты поиска

Содержание shindaiwa CS-501SX

Отзывы:

Похожие инструкции для shindaiwa CS-501SX

Бренды по названию

Популярные бренды