manualshive.com logo in svg

Echo shindaiwa CS-501SX, Руководство по обслуживанию

Поделиться
Скачать
Echo shindaiwa CS-501SX Скачать руководство пользователя страница 24

FUEL SYSTEM

CS-501SX, CS-501SXH

501sx

22

4-1 Inspecting air fi lter

1. Close choke shutter. Remove cleaner lid and air 
fi lter.

2. Inspect air fi lter (A). If blocked with dirt or dust, 
remove the obstruction with using brush.

2. If heavily blocked with dirt or dust, clean air fi lter 
(A) with compressed air or wash away with non-
infl ammable solvent/detergent.

 

WARNING         DANGER

Wear eye protection when working with 
compressed air. Eye damage can occur from 
fl ying particles.

A

D

C

4-2  Inspecting fuel cap and fuel strainer

1. Remove fuel cap.

2. Inspect fuel cap for cracks and O-ring (A) for 
cuts or damage, and replace with new one as re-
quired.

3. Replace fuel cap (B) if damaged.

4. Pull fuel strainer (C) from fuel tank using a wire 
hook (D). Clean fuel strainer. Replace if defective 
or heavily soiled.

5. Reinstall fuel cap.

A

B

Содержание shindaiwa CS-501SX

















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды