manualshive.com logo in svg

Echo shindaiwa CS-501SX, Руководство по обслуживанию

Поделиться
Скачать
Echo shindaiwa CS-501SX Скачать руководство пользователя страница 51

ENGINE

CS-501SX, CS-501SXH
501sx

49

8-3 Inspecting muffl er and exhaust port

1. Remove cleaner lid, air fi lter and cylinder cover.

2. Remove muffl er with muffl er gasket.

3. Inspect cylinder exhaust port and clean the port 
using wooden or plastic stick if carbon is found.

NOTE:

 When cleaning exhaust port, always posi-

tion piston at Top Dead Center (TDC) to prevent 
carbon from entering cylinder. Do not use metal 
tool, and be careful not to scratch piston or cylin-
der.

NOTE:

 Replace muffl er gasket with new one when 

removing muffl er.

4. Remove exhaust guides (A) and spark arrestor 
screen (B) from muffl er.

5. Remove carbon deposits from spark arrestor 
screen and exhaust guides. If screen has heavy 
deposits, replace with new one.

6. Reinstall spark arrestor screen and exhaust 
guides to muffl er.

7. Reinstall muffl er with new muffl er gasket.

NOTE:

 Before reinstalling muffler, apply 2-stroke 

oil on muffl er gasket surface and temporarily paste 
muffl er gasket (C) on cylinder as shown, in order 
to avoid damage to muffl er gasket from wall (D) of 
crankcase.

NOTE:

 New bolts for bolt hole (E) and (F) are pre-

coated with sealant on the thread. If the sealant 
is peeled off, apply thread locking sealant (Loctite 
#242, ThreeBond #1324 or equivalent).

B

A

C

F

D

E

Содержание shindaiwa CS-501SX

















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды