Echo shindaiwa 402s Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 64

Echo shindaiwa 402s Скачать руководство пользователя страница 24

ASSEMBLY

402S

24

X7503256304

© 11/23 ECHO Incorporated

5.

Remove guide bar and saw

chain if necessary.

Note: See “Maintenance and

Care” section for guide

bar/saw chain

maintenance procedures.

6.

Mount guide bar on studs (E)

and slide toward sprocket (F) to

make saw chain installation

easier. Install saw chain around

sprocket (F) and guide bar.

Make sure chain cutters are on

top of guide bar and facing

forward as shown.

7.

Install sprocket guard cover (C) over guide bar studs (E). Make sure

chain tension adjuster pin (H) fits into the guide bar adjuster hole (G),

and brake band (J) is positioned around clutch drum. Tighten sprocket

guard nuts (D) finger tight.

8.

Turn saw over, and check brake

band (J) for correct position on

clutch drum. If brake band is

not in place around drum,

remove sprocket guard cover

(C), and reinstall. Tighten

sprocket guard nuts (D) finger

tight.

9.

Adjust saw chain tension, as

instructed in “Adjusting Chain

Tension”.

H

B

D

C

J

G

E

F

J

«
...
22
23
24
25
26
...
»

Содержание shindaiwa 402s

































































Отзывы:

Нет отзывов