Echo Quickvent QV-8000 Type 1 Скачать руководство пользователя страница 3

Страница: 3 / 30

QV-8000 TYPE1-E

INTRODUCTION

DANGER

• This system is designed for use with a

special bar and chain for fire department
application. This system should not be used
for conventional wood cutting applications.

• Review ECHO Safety Chain Saw Manual and

note exceptions as listed below.

• If the unit is modified for conventional wood

cutting operations, read rules for safe
operation and instructions carefully in the
corresponding CS-8000 TYPE1-E ECHO
Chain Saw Instruction Manual and the
ECHO Chain Saw Safety Manual. Use only
the guide bar and chain combinations listed
in the instruction manual with a Kick Guard
installed on the guide bar. A free copy of
the Chain Saw Safety Manual can be
obtained from your ECHO dealer or by
writing ECHO, INCORPORATED, 400
Oakwood Road, Lake Zurich, IL 60047-1564.

The ECHO QuikVent™ System is a chain saw
specially designed for use by trained fire fighters to
ventilate, trench and breach burning structures.
This manual provides the information necessary for
operation and maintenance of the saw.

CONTENTS

Page No.

Symbols and signs .....................................................................................................

Safety .........................................................................................................................

Description ................................................................................................................. 7

Operation (Pre-Ventilation Procedures)...................................................................... 8

Troubleshooting .......................................................................................................... 14

Maintenance ............................................................................................................... 16

Specifications ............................................................................................................. 27

Specifications, descriptions and illustrative material in this literature are as accurate as

known at the time of publication, but are subject to change without notice. Illustrations

may include optional equipment and accessories, and may not include all standard

equipment.

Содержание Quickvent QV-8000 Type 1































Результаты поиска

Содержание Quickvent QV-8000 Type 1

Отзывы:

Бренды по названию

Популярные бренды

Echo Quickvent QV-8000 Type 1, Инструкция по эксплуатации

Результаты поиска

Содержание Quickvent QV-8000 Type 1

Отзывы:

Бренды по названию

Популярные бренды