manualshive.com logo in svg

Echo Quickvent QV-8000 Type 1, Инструкция по эксплуатации

Поделиться
Скачать
Echo Quickvent QV-8000 Type 1 Скачать руководство пользователя страница 19

17

QV-8000 TYPE1-E

MAINTENANCE

Clean entire system
(After Each Use)

1. Clean bar and chain with a 50 - 50 mixture of

kerosene and machine oil.

2. Remove the guide bar and clean the clutch and

brake mechanism with a 50 - 50 mixture of
kerosene and machine oil.

3. Clean the exterior of the saw with a non-

flammable solvent.

Air cleaner cover

Cleaner cover knob bolt

Spark plug

Cylinder cover

Air filter

Tighten nuts and bolts
(After Each Use)

1. Make sure all fasteners on the saw are tight.

2. Replace those found to be faulty.

Clean air filter
(After Each Use)

1. Close choke.

2. Loosen thumb bolt and remove air cleaner cover.

3. Remove any loose particles from area.

4. Remove air filter.

5. Carefully brush dirt from filter or clean with a

non-flammable solvent if necessary.

6. Install air filter.

7. Install air cleaner cover and tighten thumb bolt.

NOTE

• If air filter is excessively dirty, or no longer fits

properly, replace it.

• Allow all parts to air dry.

Содержание Quickvent QV-8000 Type 1































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды