manualshive.com logo in svg

Echo Quickvent QV-8000 Type 1, Инструкция по эксплуатации

Поделиться
Скачать
Echo Quickvent QV-8000 Type 1 Скачать руководство пользователя страница 20

18

QV-8000 TYPE1-E

MAINTENANCE

Sharpen chain
(As Needed)

1. Follow instructions included with sharpening kit.

2. Refer to page 26 for ECHO part number.

○ ○ ○ ○ ○

○ ○ ○ ○ ○

○ ○ ○ ○

Nuts

Tension screw

Adjust chain tension
(After Each Use)

1. Loosen nuts just enough to allow guide bar to

slide when tension screw is turned.

2. Turn tension screw clockwise to take up chain

slack.

3. Hold the nose of the bar up with your gloved

hand.

4. Gradually turn tension screw clockwise until the

drive links are drawn up into the bar.

5. Pull chain along bar with your gloved hand to

check for binding.

6. Back off tension screw if necessary.

7. Tighten nuts while holding bar in position.

Direction to
tension the chain

NOTE

Do not sharpen carbide chain with standard file.

IMPORTANT

Always loosen sprocket guard nuts before
turning the chain tension adjuster, otherwise the
sprocket guard and tensioner will be damaged.

Proper tension

Improper tension

Содержание Quickvent QV-8000 Type 1































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды