Echo Power Edger PE-265 Скачать руководство пользователя

Страница: 6 / 32

warning

Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all

openings.

•

ALWAyS

stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop

before removing obstructions, clearing debris, or servicing unit.

•

DO NOT

start or operate unit unless all guards and protective covers are properly assembled to unit.

•

NEVER

reach into any opening while the engine is running. Moving parts may not be visible through openings.

equIpment

warning

Use only ECHO approved attachments. Serious injury may result from the use of a non approved attachment combi-

nation. ECHO, INC. will not be responsible for the failure of cutting devices, attachments or accessories which have

not been tested and approved by ECHO. Read and comply with all safety instructions listed in this manual and safety

manual.

PRODUCT EMISSION DURABILITY (EMISSION COMPLIANCE PERIOD)

The 300 hour emission compliance period is the time span selected by the manufacturer certifying the engine emis-

sions output meets applicable emissions regulations, provided that approved maintenance procedures are followed as

listed in the Maintenance Section of this manual.

An Emission Control Label

is located on the engine. (This is an EXAMPLE ONLY, information on label varies by

engine FAMILY).

• Check unit for loose/missing nuts, bolts and screws. Tighten and/or replace as needed.

• Inspect shield for damage, and that shield is

securely

in place. Replace if shield is damaged or missing.

• Check that the cutting attachment is firmly attached and in safe operating condition.

• Check that front handle is adjusted for safe, comfortable operation. See Assembly for proper adjustment.

warning

Check fuel system for leaks due to fuel tank damage, especially if the unit is dropped. If damage or leaks are

found, do not use unit, otherwise serious personal injury or property damage may occur. Have unit repaired by an

authorized servicing dealer before using.

mIssIon

ontrol

(

exhaust

evaporatIve

)

EPA 2010 and Later and/or C.A.R.B. TIER III

The emission control system for the engine is EM/TWC (Engine Modification and 3-way Catalyst) and for the fuel tank

the Control System is EVAP (Evaporative Emissions) or N (for nylon tank). Evaporative emission may be applicable to

California models only.

Содержание Power Edger PE-265

































Результаты поиска

Содержание Power Edger PE-265

Отзывы:

Похожие инструкции для Power Edger PE-265

Бренды по названию

Популярные бренды

Echo Power Edger PE-265, Руководство оператора

Результаты поиска

Содержание Power Edger PE-265

Отзывы:

Похожие инструкции для Power Edger PE-265

Бренды по названию

Популярные бренды