background image

14

startIng

 

cold

 

engIne

   warning

The attachment will operate immediately when the engine starts 

and could result in loss of control and possible serious injury. Keep 

movable parts of the attachment off the ground and away from 

objects that could become entangled or thrown.

1. 

Stop Switch

 

Move stop switch (A) away from the STOP position.

2. 

Choke

 

Move choke (B) to “Cold Start” (

) Position.

3. 

Purge Bulb

 

Pump purge bulb (C) until fuel will be visible and flows freely in  

the clear fuel tank return line. Pump bulb an additional 4 or 5  

times.

4.

 

Recoil Starter

 

Lay the unit on a flat area and keep movable attachment parts clear 

of all obstacles. Firmly grasp right hand grip with left hand and 

fully depress throttle trigger to wide open position. Rapidly pull 

recoil starter handle/rope (D) until engine fires (or maximum five 

[5] pulls).

5.

 

Choke

 

After engine fires or five (5) pulls, move choke lever back to “Run” 

(

) position. Hold throttle trigger fully depressed and pull starter 

handle/rope until engine starts and runs. Release throttle trigger 

and allow unit to warm up at idle for several minutes.

NOTE

If engine does not start with choke in “Run” position after 5 pulls, 

repeat instructions 2 - 5.

6.  After engine warm up, gradually depress throttle trigger to increase 

engine RPM to operating speed.

C

D

a

B

D

Содержание Power Edger PE-265

































Отзывы:

Похожие инструкции для Power Edger PE-265