background image

4

 

  DANGER

Fuel is VERY flammable. Use extreme care when mixing, storing
or handling, or serious personal injury may result.
- Use an approved fuel container.
- DO NOT smoke near fuel.
- DO NOT allow flames or sparks near fuel.
- Fuel tanks/cans may be under pressure.

Always loosen fuel caps slowly allowing pressure to equalize.

- NEVER refuel a unit when the engine is HOT!
- NEVER refuel a unit with the engine running.
- DO NOT fill fuel tanks indoors.

ALWAYS fill fuel tanks outdoors over bare ground.

- Securely tighten fuel cap after refuelling.
- Inspect for fuel leakage.

If fuel leakage is found, do not start or operate unit until leakage
is repaired.

After Refuelling;

- Wipe any spilled fuel from the unit.
- Move at least 3 m from refuelling location before starting.

After Use;

- DO NOT store a unit with fuel in its tank.

Leaks can occur.
Return unused fuel to an approved fuel storage container.

 

  WARNING

Hedge Clipper users risk injury to themselves and others if the shaft hedge clipper is used improperly and or
safety precautions are not followed. Proper clothing and safety gear must be worn when operating a shaft
hedge clipper.

EQUIPMENT

Before operation a complete check of the unit must be performed;
- Check unit for loose/missing nuts, bolts and screws. Tighten and/

or replace as needed.

- Inspect fuel lines, tank and area around carburettor for fuel leaks.

DO NOT operate unit if leaks are found.

- Check that the blade assembly is firmly attached and in safe

operating condition. Dull, loose or damaged blades should not be
used.

FUEL

PERSONAL CONDITION & SAFETY EQUIPMENT

3 m

Содержание HCAA-2400A



















Отзывы: