background image

EA-410

SAFETY

© 10/2013 ECHO Inc.

X7504220703

7

The ignition components

 

of this machine generate an electromagnetic field

 

during operation which 

may interfere with some pacemakers.

 

To reduce the risk of serious or fatal injury, persons with 

pacemakers should consult with their physician and the pacemaker manufacturer before operating 
this machine.

 

In the absence of such information, ECHO does not recommend the use of

 

ECHO 

products by anyone

 

who has a pacemaker.

Vibration and Cold

It is believed that a condition called Raynaud’s Phenomenon, 
which affects the fingers of certain individuals, may be brought 
about by exposure to vibration and cold. Exposure to vibration 
and cold may cause tingling and burning sensations, followed 
by loss of color and numbness in the fingers. The following 
precautions are strongly recommended, because the minimum 
exposure, which might trigger the ailment, is unknown.

• Keep your body warm, especially the head, neck, feet, ankles, 

hands, and wrists.

• Maintain good blood circulation by performing vigorous arm exercises during frequent work breaks, and 

also by not smoking.

• Limit the hours of operation. Try to fill each day with jobs where operating the unit or other hand-held 

power equipment is not required.

• If you experience discomfort, redness, and swelling of the fingers followed by whitening and loss of feeling, 

consult your physician before further exposing yourself to cold and vibration.

Repetitive Stress Injuries

It is believed that overusing the muscles and tendons of the 
fingers, hands, arms, and shoulders may cause soreness, 
swelling, numbness, weakness, and extreme pain in those 
areas. Certain repetitive hand activities may put you at a high 
risk for developing a Repetitive Stress Injury (RSI). An extreme 
RSI condition is Carpal Tunnel Syndrome (CTS), which could 
occur when your wrist swells and squeezes a vital nerve that 
runs through the area. Some believe that prolonged exposure to 
vibration may contribute to CTS. CTS can cause severe pain for 
months or even years.

To reduce the risk of RSI/CTS, do the following: 

• Avoid using your wrist in a bent, extended, or twisted position. Instead try to maintain a straight wrist 

position. Also, when grasping, use your whole hand, not just the thumb and index finger.

• Take periodic breaks to minimize repetition and rest your hands.

• Reduce the speed and force with which you do the repetitive movement.

• Do exercise to strengthen the hand and arm muscles.

• Immediately stop using all power equipment and consult a doctor if you feel tingling, numbness, or pain in 

the fingers, hands, wrists, or arms. The sooner RSI/CTS is diagnosed, the more likely permanent nerve 
and muscle damage can be prevented.

Содержание EA-410





































Отзывы: