Echo CS-670 Скачать руководство пользователя страница 5

Страница: 5 / 26

CS-670

NOMENCLATURE OF PARTS

1. Operator’s manual - Included with unit.

Read before operation and keep for future
reference to learn proper, safe operating
techniques.

2. Safety manual - Describe operating and safety

instructions for this chain saw.

3. Front hand guard - Guard between the front

handle and the saw chain for protecting the
hand from injuries and aiding in control of the
chain saw if the hand slips off the handle.
This guard is used to activate the chain
brake which is to stop the saw chain rotation.

4. Air cleaner cover - Covers air cleaner.

5. Rear handle (for the right hand) - Support

handle located towards the rear of the
engine housing.

6. Choke control knob - Device for enriching the

fuel/air mixture in the carburetor to aid cold
starting.

7. Rear hand guard - Extension on the lower part

of the rear handle for protecting the hand
from the chain if it breaks or degrooves.

8. Clutch cover - Protective cover to the guide

bar, saw chain, clutch and sprocket when the
chain saw in use.

9. Chain tension adjuster - This is device to

adjust chain tension.

10. Chain catcher - A projection designed to

reduce the risk of the operator’s right hand
from being hit by a chain which has broken
or derailed from the guide bar during cutting.

11. Guide bar - The part that supports and guide

the saw chain.

12. Bar tip guard - Anti-kickback device attached

on the bar nose.

13. Saw chain - Chain, serving as a cutting tool.

14. Spiked bumper - Device, fitted in front of the

guide bar mounting point, acting as a pivot
when in contact with a tree or log.

15. Cylinder cover - The cooling airflow grill.

It covers the cylinder, spark plug and
silencer.

16. Front handle ( for the left hand ) - Support

handle located at the front of the engine
housing.

17. Oil tank cap - For closing the oil tank.

18. Starter handle - Pull handle slowly until starter

engages then quickly and firmly. When
engine starts, return handle slowly.
DO NOT let handle snap back or damage to
unit will occur.

19. Fuel tank cap - For closing the fuel tank.

20. Manual oil pump - Device for proper

lubrication of chain.

21. Throttle trigger - Device activated by the

operator’s finger, for controlling the engine
speed.

22. Throttle trigger lockout - A safety lever which

must be depressed before the throttle trigger
can be activated in order to prevents the
accidental operation of the throttle trigger.

23. Ignition switch - Device for connecting and

disconnecting the ignition system and thus
allowing the engine to be started or stopped.

Содержание CS-670



























Результаты поиска

Содержание CS-670

Отзывы:

Похожие инструкции для CS-670

Бренды по названию

Популярные бренды

Echo CS-670, Руководство оператора

Результаты поиска

Содержание CS-670

Отзывы:

Похожие инструкции для CS-670

Бренды по названию

Популярные бренды