background image

CS-450P

SAFETY

© 01/2014 ECHO Inc.

X7503197605

5

Correct Use Of Chain Brake

Chain Brake Operation

• Set the lever in the unlocked position before starting to cut.

• If the brake is tripped by kickback reaction, the chain will stop 

immediately. Release the throttle to avoid possible damage to 
the engine or clutch.

• Do not attempt to operate the engine with the brake locked.

Testing The Brake

• Start the engine on a solid level surface and run at a fast idle 

until warm.

• Hold the saw firmly by the handles and accelerate the engine 

to a fast idle.

• Slowly operate the chain brake lever while holding the saw 

firmly on the ground.  When the brake lever trips, the chain 
should stop. Immediately release the throttle trigger.

Do not allow the saw to tip forward in order to avoid damage to the chain.

If the chain does not stop immediately, return the saw to your authorized ECHO dealer for repair.

Note: 

• For practice, while cutting a small tree, push the lever forward to lock the brake.

• Confirm that the brake works properly before each use.

• If the chain brake is clogged with wood chips, function of the brake may deteriorate. Always keep the 

device clean.

• Do not increase engine RPM's while the chain brake is locked.

The installation of a chain brake may be mandatory by law or as stipulated by insurance regulations in your 
area of operation.  You should inquire through local government offices, your employer or your local dealer to 
ensure that your chain saw conforms to the required safety standard. 

ECHO chain brakes have been designed and tested to comply with international safety standards as follows.

USA: ANSI Standard B175.1 Safety Requirement for chain saws

ANSI Standard B175.1 stipulates that the brake shall stop the chain 0.12 seconds at an engine speed 
of 13,500 r/min. It is the responsibility of the owner/operator to ensure that the brake is serviced, 
adjusted and tested strictly in accordance with the instructions as detailed here in order to ensure 
that the brake performance is maintained in compliance with the Standard B175.1. 

Locked

Unlocked

Содержание CS-450P













































Отзывы: