Echo CS-450P Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 44

background image

32

X7503197605

© 01/2014 ECHO Inc.

MAINTENANCE

CS-450P

Exhaust Port Cleaning

Level 2.

1. Remove air cleaner cover and remove spark plug lead.

2. Remove guide bar and saw chain. See "Guide Bar and Saw

Chain Installation/Removal."

3. Remove muffler support bracket (A).

4. Place piston at top dead center.

5. Remove muffler. Check parts for wear or damage, and

replace if necessary.

6. Use a wood or plastic scraping tool to clean deposits from

cylinder exhaust port.

Never use a metal tool to scrape carbon from the exhaust port.
Do not scratch the cylinder or piston when cleaning the exhaust
port. Do not allow carbon particles to enter the cylinder.

7. Install muffler. Tighten muffler mounting bolts (or nuts) to

7-11 N•m (60-95 in•lbf).

8. Install muffler support bracket (A).

9. Install guide bar and saw chain. See "Guide Bar and Saw

Chain Installation/Removal."

10. Install spark plug lead and air cleaner cover.

11. Start engine, and warm to operating temperature. Stop

engine.

12. Remove air cleaner cover and remove spark plug lead.

13. Remove guide bar and saw chain. See "Guide Bar and Saw Chain Installation/Removal."

14. Remove muffler support bracket.

15. Re-tighten mounting bolts (or nuts) to 7-11 N•m (60-95 in•lbf).

16. Install muffler support bracket.

17. Install guide bar and saw chain. See "Guide Bar and Saw Chain Installation/Removal."

18. Install spark plug lead and air cleaner cover.

Parts Required:

As needed: Muffler gasket

A

«
...
30
31
32
33
34
...
»

Содержание CS-450P













































Отзывы:

Нет отзывов

Похожие инструкции для CS-450P

Бренд: Zenoah Страницы: 17

Бренд: Parkside Страницы: 132

Бренд: Nakayama Страницы: 75

Бренд: SIP Страницы: 8

Бренд: Ribiland Страницы: 94

Бренд: Bushranger Страницы: 16

Бренд: Baumr-AG Страницы: 29

Бренд: Echo Страницы: 64

Бренд: ICFR Страницы: 64

Бренд: Jonsered Страницы: 280

Бренд: Homelite Страницы: 32

Бренд: Homelite Страницы: 120

Бренд: Stiga Страницы: 2

Бренд: Garland Страницы: 120

Бренд: XTline Страницы: 100

Бренд: Oleo-Mac Страницы: 216

Бренд: Makita Страницы: 124

Бренд: Meec tools Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды