Echo CS-370ES Скачать руководство пользователя страница 62

Страница: 62 / 69

GUIDE BAR MOUNTING SYSTEM

CS-370ES
CS-420ES

10-1

Replacing chain tensioner

1. Remove sprocket guard from the unit.

2. Remove outer sprocket guard plate (A) from
sprocket guard. Remove tensioner screw (B),
chain tensioner (C) and bevel gears (D) (E) and
collar (F).

3. Inspect them for damage or wear. Replace as
required.

4. Install bevel gear (E) into sprocket guard.

5. Screw chain tensioner (C) on tensioner screw
(B).

6. Set bevel gear (D) in collar (F) and insert ten-
sioner screw (B) with chain tensioner (C) in bevel
gear with collar (F).

7. Install sub-assembled tensioner screw in slot (G)
of sprocket guard, con

rming engagement of bevel

gear (D) and (E).

8. Reinstall outer sprocket guard plate (A).

10-2 Replacing guide bar stud

1. Remove oil cap and empty oil in tank.

2. Remove inner sprocket guard plate.

3. Push defective guide bar stud into oil tank by
tapping with copper hammer and make the guide
bar stud breaks through plastic layer covering head
of the stud. Remove

akes of plastic and stud from

oil tank.

Содержание CS-370ES






































































Результаты поиска

Содержание CS-370ES

Отзывы:

Бренды по названию

Популярные бренды

Echo CS-370ES, Руководство по обслуживанию

Результаты поиска

Содержание CS-370ES

Отзывы:

Бренды по названию

Популярные бренды