manualshive.com logo in svg

Echo CS-370ES, Руководство по обслуживанию

Поделиться
Скачать
Echo CS-370ES Скачать руководство пользователя страница 31

29

FUEL SYSTEM

CS-370ES
CS-420ES

4-7 Adjusting carburetor (continued)

  4-7-3 Adjusting carburetor

1. Start engine and warm it up for two minutes alternating rpm between WOT (Wide Open Throttle) and
idle every 5 seconds. Turn H mixture needle anticlockwise until engine speed drops to approx. 11,000 rpm
(CS-370ES), 12,000 rpm (CS-420ES).

2. Then continue warm up cycling engine speed between WOT for 5 seconds, and idle for 5 seconds for
another minute and a half.

NOTE: Do not run engine at high speed without  load longer than 10 seconds, or engine damage may
occur.

3. Adjust L mixture needle to reach maximum engine rpm just before lean drop off.

4. Set idle engine speed to 3,800 rpm (CS-370ES, CS-420ES) by turning idle adjust screw. Engine rpm
should be stable at 3,800 +/- 10 rpm after idle adjust screw adjustment.

5. Turn L mixture needle anticlockwise reducing engine idle speed 1,200 rpm to set idle speed at 2,600
rpm. The engine idle speed range is 2,400 - 2,800 rpm.

NOTE: Engine speed must be allowed to stabilize a minimum of 20 seconds after each adjustment of L
mixture needle to assure accurate tachometer readings.

6. Before adjusting H mixture needle, WOT engine speed should be less than or equal to 11,000 rpm (CS-
370ES), 12,000 rpm (CS-420ES). If rpm is higher, turn H mixture needle anticlockwise until 11,000 rpm
(CS-370ES), 12,000 rpm (CS-420ES) is achieved. To make the final WOT engine speed adjustment, turn
H mixture needle clockwise 1/8 turn increments with the engine at idle, then squeeze throttle trigger and
check WOT engine speed. The final WOT engine speed should fall within 11,700 to 12,300 rpm (CS-
370ES), 12,400 to 12,800 rpm (CS-420ES) range.

7. After adjusting carburetor, screw new limiter cap
on the limiter cap removal tool 91019 (C)
anticlockwise approx. 2 turns as shown, and put the
limiter caps on L and H mixture needles respectively
and remove the limiter cap tool. And then press the
caps on L and H mixture needles with bar tool.

NOTE : Align the limiter cap’s tabs (A) with locating
slots (B) in extended housing of carburetor.

IMPORTANT: The limiter caps must be installed L and H mixture needles to comply with Emission
Directive.

8. Start engine, and verify engine idle speed ranges from 2,400 to 2,900 rpm (CS-370ES, CS-420ES),
and WOT engine speed  ranges from 11,500 to 12,500 rpm (CS-370ES), 12,300 to 13,000 rpm (CS-
420ES). Make sure chain does not rotate when engine is idling. When final adjustment is completed, the
engine should idle, accelerate smoothly, and attain WOT per above specification.

NOTE: Initial carburetor settings for idle adjust screw, L and H mixture needles are intended to start and
run the engine before final carburetor adjustments are made to conform the unit to meet Emission Directive.
Actual turns required for engine operation may vary.

NOTE: Engine WOT and idle speed rpm in field operation may vary from final adjustment specifications
due to changing ambient conditions and fuel. Safe engine rpm variances should be within the WOT, idle
speed ranges listed in section 1-1, otherwise carburetor should be readjusted.

H

L

A

B

B

A

C

Содержание CS-370ES






































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды