manualshive.com logo in svg

Echo CS-370ES, Руководство по обслуживанию

Поделиться
Скачать
Echo CS-370ES Скачать руководство пользователя страница 18

16

IGNITION SYSTEM

CS-370ES
CS-420ES

3-2 Testing spark

1. Remove air cleaner cover and remove spark plug
cap from spark plug.

2. Connect spark tester 990511-30023 (A) to high
tension lead and connect tester lead (B) on spark
plug.

3. Screw in adjuster (C) until the needle tips contact.
Turn out adjuster (C) 4 turns to set spark tester gap
(D) to 4 mm (0.16 in).

4. Turn ignition switch to “RUN” position. Pull starter
grip several times.

5. If spark is steady in blue or white at the tester
gap, ignition system is considered good. Go to
inspecting spark plug.

6. If no spark exists or spark is intermittent in yellow,
orange, or red, continue with further inspection.

DANGER

*Do not test near spark plug hole without
spark plug installed, otherwise there is a
chance to ignite fuel mixture inside cylinder
and cause serious personal injury.
*Do not touch metal parts of spark tester
while performing the test to avoid receiving
electrical shock.

DANGER

Do not check spark in area where gasoline is
spilled or flammable gases may exist.

3-3 Inspecting spark plug

1. Remove spark plug to inspect for fouling, cracked
or broken insulator, or rounded center electrode.
Clean or replace spark plug as required.

2. Set spark plug gap (A) by bending outer electrode
(B).

Standard : 0.6 to 0.7 mm (0.024 to 0.028 in)

3. If engine does not start after cranking several
times, inspect if spark plug is wet or dry. If it is
excessively wet or dry, inspect fuel system.

A

B

GASO
    LINE

A

B

C

D

Содержание CS-370ES






































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды